Custom Programmed 3-PLL Clock Synthesizer / Multiplier / Divider

The CDC706 is one of the smallest and powerful PLL synthesizer / multiplier / divider available today. Despite its small physical outlines, the CDC706 is very flexible. It has the capability to produce an almost independent output frequency from a given input frequency.
The input frequency CAN be derived from a LVCMOS, differential input Clock or a single crystal. The appropriate input waveform CAN be selected via the SMBus data Interface controller.
To achieve an independent output frequency the reference divider M and the feedback divider N for each PLL CAN be set to values from 1 up to 511 for the M-Divider and from 1 up to 4095 for the N-Divider. The PLL-VCO (voltage controlled oscillator) frequency than is routed to the free progra f28 mmable output switching matrix to any of the six outputs. The switching matrix includes an additional 7-bit post-divider (1-to-127) and an inverting Logic for each output.
The deep M/N divider ratio allows the generation of zero ppm Clocks from any reference input frequency (e.g., a 27-MHz).
The CDC706 includes three PLLs of those one supports SSC (spread-spectrum clocking). PLL1, PLL2, and PLL3 are designed for frequencies up to 300 MHz and optimized for zero-ppm applications with wide divider factors.
PLL2 also supports center-spread and down-spread spectrum clocking (SSC). This is a common technique to reduce electro-magnetic interference. Also, the slew-rate controllable (SRC) output edges minimize EMI noise.
Based on the PLL frequency and the divider settings, the internal loop Filter components will be automatically adjusted to achieve high stability and optimized jitter transfer characteristic of the PLL
The device provides customized applications. It is preprogrammed with a factory default configuration and CAN be reprogrammed to a different application configuration via the serial SMBus Interface
Two free programmable inputs, S0 and S1, CAN be used to control for each application the most demanding Logic control settings (outputs disable to low, outputs 3-state, power down, PLL bypass, etc).
The CDC706 has three power supply pins, VCC, VCCOUT1, and VCCOUT2. VCC is the power supply for the device. It operates from a single 3.3-V supply voltage. VCCOUT1 and VCCOUT2 are the power supply pins for the outputs. VCCOUT1 supplies the outputs Y0 and Y1 and VCCOUT2 supplies the outputs Y2, Y3, Y4, and Y5. Both outputs supplies CAN be 2.3 V to 3.6 V. At output voltages lower than 3.3 V, the output current drive is limited.
The CDC706 is characterized for operation from -40C to 85C.
By Texas Instruments
Part Manufacturer Description Datasheet Samples
CDC706PW Texas Instruments Custom Programmed 3-PLL Clock Synthesizer / Multiplier / Divider 20-TSSOP
CDC706PWG4 Texas Instruments Custom Programmed 3-PLL Clock Synthesizer / Multiplier / Divider 20-TSSOP
CDC706PWR Texas Instruments Custom Programmed 3-PLL Clock Synthesizer / Multiplier / Divider 20-TSSOP
CDC706PWRG4 Texas Instruments Custom Programmed 3-PLL Clock Synthesizer / Multiplier / Divider 20-TSSOP
CDC706 's PackagesCDC706 's pdf datasheet
CDC706PW TSSOP
CDC706PWG4 TSSOP
CDC706PWR TSSOP
CDC706PWRG4 TSSOP




CDC706 Pinout, Pinouts
CDC706 pinout,Pin out
This is one package pinout of CDC706,If you need more pinouts please download CDC706's pdf datasheet.

CDC706 Application circuits
CDC706 circuits
This is one application circuit of CDC706,If you need more circuits,please download CDC706's pdf datasheet.


Related Electronics Part Number

Related Keywords:

CDC706 Pb-Free CDC706 Cross Reference CDC706 Schematic CDC706 Distributor
CDC706 Application Notes CDC706 RoHS CDC706 Circuits CDC706 footprint