The OPA2683 provides a new level of performance for dual, very low-power, wideband, current-feedback amplifiers. This CFBPLUS amplifier is among the first to use an internally closed-loop input buffer stage that significantly enhances performance over earlier ...
The OPA2684 provides a new level of performance in low-power, wideband, current-feedback (CFB) amplifiers. This CFBPLUS amplifier is among the first to use an internally closed-loop input buffer stage that enhances performance significantly over earlier ...
The OPA2691 sets a new level of performance for broadband dual current-feedback op amps. Operating on a very low 5.1mA/ch supply current, the OPA2691 offers a slew rate and output power normally associated with a much higher supply current. A new output stage ...
The OPA2694 is a dual, ultra-wideband, low-power, current feedback operational amplifier featuring high slew rate and low differential gain/phase errors. An improved output stage provides 70mA output drive with < 1.5V output voltage headroom. Low supply ...
The OPA3691 sets a new level of performance for broadband, triple current-feedback op amps. Operating on a very low 5.1mA/ch supply current, the OPA3691 offers a slew rate and output power normally associated with a much higher supply current. A new output ...
The OPA3690 represents a major step forward in unitygain stable, voltagefeedback op amps. A new internal architecture provides slew rate and fullpower bandwidth previously found only in wideband, currentfeedback op amps. A new output stage architecture ...
The OPA3684 provides a new level of performance in lowpower, wideband, currentfeedback (CFB) amplifiers. This CFBPLUS amplifier among the first to use an internally closedloop input buffer stage that enhances performance significantly over earlier lowpower CFB ...
The OPA695 is a very high bandwidth, current-feedback op amp that combines exceptional 4300V/??s slew rate and low input voltage noise to deliver a precision low cost, high dynamic range Intermediate Frequency (IF) amplifier. Optimized for high gain operation, ...
The OPA694 is an ultrawideband, lowpower, current feedback operational amplifier featuring high slew rate and low differential gain/phase errors. An improved output stage provides 80mA output drive with < 1.5V output voltage headroom. Low supply current with > ...
The OPA693 provides an easy to use, broadband, fixed gain buffer amplifier. Depending on the external connections, the internal resistor network may be used to provide either a fixed gain of +2 video buffer or a gain of 1 voltage buffer. Operating on a low ...
The OPA691 sets a new level of performance for broadband current feedback op amps. Operating on a very low 5.1mA supply current, the OPA691 offers a slew rate and output power normally associated with a much higher supply current. A new output stage ...
The OPA683 provides a new level of performance in very low-power, wideband, Current Feedback Amplifiers This CFBplus amplifier is among the first to use an internally closed-loop input buffer stage that enhances performance significantly over earlier ...
The OPA684 provides a new level of performance in low-power, wideband, current-feedback (CFB) amplifiers. This CFBplus amplifier is the first to use an internally closed-loop input buffer stage that enhances performance significantly over earlier low-power CFB ...
The THS3091 and THS3095 are high-voltage, low-distortion, high-speed, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for applications requiring large, linear output signals such as Pin, Power FET, and VDSL line ...
The THS3061 (single) and THS3062 (dual) are high-voltage, high slew-rate Current Feedback Amplifiers utilizing Texas Instruments BICOM-1 process. Designed for low-distortion with a high slew rate of 7000 V/us, the THS306x amplifiers are ideally suited for ...
The THS3061 (single) and THS3062 (dual) are high-voltage, high slew-rate Current Feedback Amplifiers utilizing Texas Instruments BICOM-1 process. Designed for low-distortion with a high slew rate of 7000 V/us, the THS306x amplifiers are ideally suited for ...
The THS3092 and THS3096 are dual high-voltage, low-distortion, high speed, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for applications requiring large, linear output signals such as Pin, Power FET, and VDSL line ...
The THS3091 and THS3095 are high-voltage, low-distortion, high-speed, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for applications requiring large, linear output signals such as Pin, Power FET, and VDSL line ...
The THS3092 and THS3096 are dual high-voltage, low-distortion, high speed, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for applications requiring large, linear output signals such as Pin, Power FET, and VDSL line ...
The THS3110 and THS3111 are low-noise, high-voltage, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for todays high performance applications.
The THS3110 features a powerdown pin (PD) that puts the amplifier in low ...
The THS3110 and THS3111 are low-noise, high-voltage, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for todays high performance applications.
The THS3110 features a powerdown pin (PD) that puts the amplifier in low ...
The THS3112/5 are low-noise, high-speed Current Feedback Amplifiers ideal for any application requiring high output current. The low noninverting current noise of 2.9 pA/Hz and the low inverting current noise of 10.8 pA/Hz increase signal to noise ratios for ...
The THS3112/5 are low-noise, high-speed Current Feedback Amplifiers ideal for any application requiring high output current. The low noninverting current noise of 2.9 pA/Hz and the low inverting current noise of 10.8 pA/Hz increase signal to noise ratios for ...
The THS3120 and THS3121 are low-noise, high-voltage, high output current drive, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for today\\\\\\\'s high
performance applications.
The THS3120 offers a power saving mode ...
The THS3120 and THS3121 are low-noise, high-voltage, high output current drive, current-feedback amplifiers designed to operate over a wide supply range of 5 V to 15 V for today\\\\\\\'s high
performance applications.
The THS3120 offers a power saving mode ...
The THS3201 is a wide-band, high-speed current-feedback amplifier, designed to operate over a wide supply range of 3.3 V to 7.5 V for todays high performance applications.
The wide supply range combined with distortion as low as 74 dBc at 10 MHz, plus an ...
The THS3202 is part of the high performing current feedback amplifier family developed in BiCOMII technology. Designed for low-distortion with a high slew rate of 9000V/??s, the THS320x family is ideally suited for applications driving loads sensitive to ...
The THS3122/5 are low-noise, high-speed Current Feedback Amplifiers with high output current drive. This makes them ideal for any application that requires low distortion over a wide frequency with heavy loads. The THS3122/5 can drive four serially terminated ...
The THS6012 contains two high-speed drivers capable of providing 400 mA output current (min) into a 25 load. These drivers can be configured differentially to drive a 50-VPP output signal over low-impedance lines. The drivers are Current Feedback Amplifiers ...
The THS6022 contains two high-speed drivers capable of providing 200-mA output current (minimum) into a 50- load. These drivers can be configured differentially to drive a 50-V p-p output signal over low-impedance lines. The drivers are current feedback ...
The THS6032 is a low-power line driver ideal for asymmetrical digital subscriber line (ADSL) applications. This device contains two high-current, high-speed current-feedback drivers, which can be configured differentially for driving ADSL signals at the ...
The THS6042/3 is a high-speed line driver ideal for driving signals from the remote terminal to the central office in asymmetrical digital subscriber line (ADSL) applications. It can operate from a 12-V supply voltage while drawing only 8.2 mA of supply ...
The THS3122/THS3125 are low-noise, high-speed Current Feedback Amplifiers with high output current drive. This makes them ideal for any application that requires low distortion over a wide frequency with heavy loads. The THS3122/5 can drive four serially ...
The OPA4684 provides a new level of performance in low-power, wideband, current-feedback (CFB) amplifiers. This CFBPLUS amplifier is among the first to use an internally closed-loop input buffer stage that enhances performance significantly over earlier ...
The LMH6723,LMH6724,LMH6725 provides a 260 MHz small signal bandwidth at a gain of +2 V/V and a 600 V/?s slew rate while consuming only 1 mA from 5V supplies. The LMH6723,LMH6724,LMH6725 supports video applications with its 0.03% and 0.11 differential ...
The LMH6723,LMH6724,LMH6725 provides a 260 MHz small signal bandwidth at a gain of +2 V/V and a 600 V/?s slew rate while consuming only 1 mA from 5V supplies. The LMH6723,LMH6724,LMH6725 supports video applications with its 0.03% and 0.11 differential ...
The LMH6723,LMH6724,LMH6725 provides a 260 MHz small signal bandwidth at a gain of +2 V/V and a 600 V/?s slew rate while consuming only 1 mA from 5V supplies. The LMH6723,LMH6724,LMH6725 supports video applications with its 0.03% and 0.11 differential ...
The AD8004 is a quad, low power, high speed amplifier designed to operate on single or dual supplies. It utilizes a current back architecture and features high slew rate of 3000 V/s making the AD8004 ideal for handling large amplitude pulses. Additionally, the ...
The AD8011 is a very low power, high speed amplifier designed to operate on +5 V or 5 V supplies. With wide bandwidth, low distortion and low power, this device is ideal as a general purpose amplifier. It also can be used to replace high speed amplifiers ...
The AD8009 is an ultrahigh speed current feedback amplifier with a phenomenal 5,500 V/s slew rate that results in a rise time of 545 ps, making it ideal as a pulse amplifier. The high slew rate reduces the effect of slew rate limiting and results in the ...
The AD8001 is a low power, high speed amplifier designed to operate on 5 V supplies. The AD8001 features unique transimpedance linearization circuitry. This allows it to drive video loads with excellent differential gain and phase performance on only 50 mW of ...
The AD812 is a low power, single supply, dual video amplifier. Each of the amplifiers have 50 mA of output current and are optimized for driving one back terminated video load (150 ) each. Each amplifier is a current feedback amplifier and features gain ...
The AD8002 is a dual, low power, high speed amplifier designed to operate on 5 V supplies. The AD8002 features unique transimpedance linearization circuitry. This allows it to drive video loads with excellent differential gain and phase performance on only 50 ...
The AD8005 is an ultralow power, high speed amplifier with a wide signal bandwidth of 170 MHz and slew rate of 280 V/s. This performance is achieved while consuming only 400 A of quiescent supply current. These features increase the operating time of high ...
The EL5166 and EL5167 amplifiers are of the current feedback variety and exhibit a very high bandwidth of 1.4GHz at AV = +1 and 800MHz at AV = +2. This makes these amplifiers ideal for today\'s high speed video and monitor applications, as well as a number of ...
The EL5166 and EL5167 amplifiers are of the current feedback variety and exhibit a very high bandwidth of 1.4GHz at AV = +1 and 800MHz at AV = +2. This makes these amplifiers ideal for today\'s high speed video and monitor applications, as well as a number of ...
The EL5367 triple amplifier is of the current feedback variety and exhibits a very high bandwidth of 1GHz at AV = +1 and 800MHz at AV = +2. This makes this amplifier ideal for todays high speed video and monitor applications, as well as a number of RF and IF ...
The EL5162, EL5163, EL5262, EL5263, and EL5362 are Current Feedback Amplifiers with a bandwidth of 500MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 1.5mA and the ability to run ...
The EL5162, EL5163, EL5262, EL5263, and EL5362 are Current Feedback Amplifiers with a bandwidth of 500MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 1.5mA and the ability to run ...
The EL5164, EL5165, and EL5364 are Current Feedback Amplifiers with a very high bandwidth of 600MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 5mA and the ability to run from a ...
The EL5164, EL5165, and EL5364 are Current Feedback Amplifiers with a very high bandwidth of 600MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 5mA and the ability to run from a ...
The EL5162, EL5163, EL5262, EL5263, and EL5362 are Current Feedback Amplifiers with a bandwidth of 500MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 1.5mA and the ability to run ...
The EL5162, EL5163, EL5262, EL5263, and EL5362 are Current Feedback Amplifiers with a bandwidth of 500MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 1.5mA and the ability to run ...
The EL5162, EL5163, EL5262, EL5263, and EL5362 are Current Feedback Amplifiers with a bandwidth of 500MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 1.5mA and the ability to run ...
The EL5164, EL5165, and EL5364 are Current Feedback Amplifiers with a very high bandwidth of 600MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 5mA and the ability to run from a ...
The EL5392A is a triple current feedback amplifier with a very high bandwidth of 600MHz. This makes this amplifier ideal for todays high speed video and monitor applications. With a supply current of just 6mA per amplifier and the ability to run from a ...
The EL5462 is a current feedback amplifier with a bandwidth of 500MHz which makes this amplifier ideal for todays high speed video and monitor applications. With a supply current of just 1.5mA per amplifier and the ability to run from a single supply ...
The HFA1100 is a high-speed, wideband, fast settling current feedback amplifier built with Intersil\'s proprietary complementary bipolar UHF-1 process. It operates with single supply voltages as low as 4.5V (see Application Information section). The ...
The HFA1130 is a high speed wideband current feedback amplifier featuring programmable output limits. Built with Intersils proprietary complementary bipolar UHF-1 process, it is the fastest monolithic amplifier available from any semiconductor manufacturer.
The EL2480 is a quad current-feedback operational amplifier which achieves a -3dB bandwidth of 250MHz at a gain of +1 while consuming only 3mA of supply current per amplifier. It will operate with dual supplies ranging from 1.5V to 6V, or from single supplies ...
The EL5160, EL5161, EL5260, EL5261, and EL5360 are Current Feedback Amplifiers with a bandwidth of 200MHz and operate from just 0.75mA supply current. This makes these amplifiers ideal for todays high speed video and monitor applications. With the ability ...
The EL5160, EL5161, EL5260, EL5261, and EL5360 are Current Feedback Amplifiers with a bandwidth of 200MHz and operate from just 0.75mA supply current. This makes these amplifiers ideal for todays high speed video and monitor applications. With the ability ...
The EL5160, EL5161, EL5260, EL5261, and EL5360 are Current Feedback Amplifiers with a bandwidth of 200MHz and operate from just 0.75mA supply current. This makes these amplifiers ideal for todays high speed video and monitor applications. With the ability ...
The EL5160, EL5161, EL5260, EL5261, and EL5360 are Current Feedback Amplifiers with a bandwidth of 200MHz and operate from just 0.75mA supply current. This makes these amplifiers ideal for todays high speed video and monitor applications. With the ability ...
The EL5160, EL5161, EL5260, EL5261, and EL5360 are Current Feedback Amplifiers with a bandwidth of 200MHz and operate from just 0.75mA supply current. This makes these amplifiers ideal for todays high speed video and monitor applications. With the ability ...
The EL8108 is a dual current feedback operational amplifier designed for video distribution solutions. This device features a high drive capability of 450mA while consuming only 5mA of supply current per amplifier and operating from a single 5V to 12V ...
The HA-5020 is a wide bandwidth, high slew rate amplifier optimized for video applications and gains between 1 and 10. Manufactured on Intersils Reduced Feature Complementary Bipolar DI process, this amplifier uses current mode feedback to maintain higher ...
The HA5023 is a wide bandwidth high slew rate dual amplifier optimized for video applications and gains between 1 and 10. It is a current feedback amplifier and thus yields less bandwidth degradation at high closed loop gains than voltage feedback ...
The HA5024 is a quad version of the popular Intersil HA5020. It features wide bandwidth and high slew rate, and is optimized for video applications and gains between 1 and 10. It is a current feedback amplifier and thus yields less bandwidth degradation at ...
The HFA1105 is a high speed, low power current feedback amplifier built with Intersils proprietary complementary bipolar UHF-1 process. This amplifier features an excellent combination of low power dissipation (58mW) and high performance. The slew rate, ...
The HFA1109 is a high speed, low power, current feedback amplifier built with Intersils proprietary complementary bipolar UHF-1 process. This amplifier features a unique combination of power and performance specifically tailored for video applications.
The HFA1145 is a high speed, low power current feedback amplifier built with Intersils proprietary complementary bipolar UHF-1 process. This amplifier features a TTL/CMOS compatible disable control, pin 8, which when pulled low reduces the supply current ...
The HFA1155 is a low power, high-speed op amp and is the most recent addition to Intersils HFA1XX5 series of low power op amps and buffers. Intersil\'s proprietary complementary bipolar UHF-1 process, coupled with the current feedback architecture deliver ...
The EL5192 and EL5192A are Current Feedback Amplifiers with a very high bandwidth of 600MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 6mA and the ability to run from a single ...
The EL5193 and EL5193A are Current Feedback Amplifiers with a bandwidth of 300MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 4mA and the ability to run from a single supply ...
The EL5292 and EL5292A represent dual Current Feedback Amplifiers with a very high bandwidth of 600MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 6mA per amplifier and the ability to ...
The EL5293 and EL5293A represent dual Current Feedback Amplifiers with a bandwidth of 300MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 4mA per amplifier and the ability to run ...
The EL5393A is a triple current feedback amplifier with a bandwidth of 300MHz. This makes these amplifiers ideal for todays high speed video and monitor applications. With a supply current of just 4mA per amplifier and the ability to run from a single supply ...
The EL5191 and EL5191A amplifiers are of the current feedback variety and exhibit a very high bandwidth of 1GHz. This makes these amplifiers ideal for todays high speed video and monitor applications, as well as a number of RF and IF frequency designs.
The 5962-0625601QXC and 5962-0625602QXC are fully DSCC SMD compliant parts and the SMD data sheets are available on the DSCC website (http://www.dscc.dla.mil/pro grams/specfind/default.asp). The 5962-0625601QXC is electrically equivalent to the EL5166, the ...
The 5962-0625601QXC and 5962-0625602QXC are fully DSCC SMD compliant parts and the SMD data sheets are available on the DSCC website (http://www.dscc.dla.mil/pro grams/specfind/default.asp). The 5962-0625601QXC is electrically equivalent to the EL5166, the ...
The LT1204 is a 4-input video multiplexer designed to drive 75 ohms cables and easily expand into larger routing systems. Wide bandwidth, high slew rate, and low differential gain and phase make the LT1204 ideal for broadcast quality signal routing. Channel ...
The LT1206 is a current feedback amplifier with high output current drive capability and excellent video characteristics. The LT1206 is stable with large capacitive loads, and can easily supply the large currents required by the capacitive loading. A shutdown ...
The LT1207 is a dual version of the LT1206 high speed current feedback amplifier. Like the LT1206, each CFA in the dual has excellent video characteristics: 60MHz bandwidth, 250mA minimum output drive current, 400V/s minimum slew rate, low differential gain ...
The LT1210 is a current feedback amplifier with high output current and excellent large-signal characteristics. The combination of high slew rate, 1.1A output drive and 15V operation enables the device to deliver significant power at frequencies in the 1MHz to ...
The LT1217 is a 10MHz current feedback amplifier with DC characteristics better than many voltage feedback amplifiers. This versatile amplifier is fast, 280ns settling to 0.1% for a 10V step thanks to its 500V/s slew rate.The LT1217 is manufactured on Linear ...
The LT1227 is a current feedback amplifier with wide bandwidth and excellent video characteristics. The low differential gain and phase, wide bandwidth, and 30mA output drive current make the LT1227 well suited to drive cables in video systems. A shutdown ...
The LT1228 makes it easy to electronically control the gain of signals from DC to video frequencies. The LT1228 implements gain control with a transconductance amplifier (voltage to current) whose gain is proportional to an externally controlled current. A ...
The LT1229/LT1230 dual and quad 100MHz Current Feedback Amplifiers are designed for maximum performance in small packages. Using industry standard pinouts, the dual is available in the 8-pin miniDIP and the 8-pin SO package while the quad is in the 14-pin DIP ...
The LT1229/LT1230 dual and quad 100MHz Current Feedback Amplifiers are designed for maximum performance in small packages. Using industry standard pinouts, the dual is available in the 8-pin miniDIP and the 8-pin SO package while the quad is in the 14-pin DIP ...
The LT1252 is a low cost current feedback amplifier for video applications. The LT1252 is ideal for driving low impedance loads such as cables and filters. The wide bandwidth and high slew rate of this amplifier make driving RGB signals between PCs and ...
The LT1253 is a low cost dual current feedback amplifier for video applications. The LT1254 is a quad version of the LT1253. The amplifiers are completely isolated except for the power supply pins and therefore have excellent isolation, over 94dB at 5MHz. Dual ...
The LT1253 is a low cost dual current feedback amplifier for video applications. The LT1254 is a quad version of the LT1253. The amplifiers are completely isolated except for the power supply pins and therefore have excellent isolation, over 94dB at 5MHz. Dual ...
The LT1259 contains two independent 130MHz Current Feedback Amplifiers each with a shutdown pin. These amplifiers are designed for excellent linearity while driving cables and other low impedance loads. The LT1260 is a triple version especially suited to RGB ...
The LT1259 contains two independent 130MHz Current Feedback Amplifiers each with a shutdown pin. These amplifiers are designed for excellent linearity while driving cables and other low impedance loads. The LT1260 is a triple version especially suited to RGB ...
The LT1395/LT1396/LT1397 are single/dual/quad 400MHz Current Feedback Amplifiers with an 800V/s slew rate and the ability to drive up to 80mA of output current. The LT1395/LT1396/LT1397 operate on all supplies from a single 4V to 6V. At 5V, they draw ...
The LT1395/LT1396/LT1397 are single/dual/quad 400MHz Current Feedback Amplifiers with an 800V/s slew rate and the ability to drive up to 80mA of output current. The LT1395/LT1396/LT1397 operate on all supplies from a single 4V to 6V. At 5V, they draw ...
The LT1395/LT1396/LT1397 are single/dual/quad 400MHz Current Feedback Amplifiers with an 800V/s slew rate and the ability to drive up to 80mA of output current. The LT1395/LT1396/LT1397 operate on all supplies from a single 4V to 6V. At 5V, they draw ...
The LT1399 and LT1399HV contain three independent 300MHz Current Feedback Amplifiers each with a shutdown pin. The LT1399HV is a higher voltage version of the LT1399. The LT1398 is a two amplifier version of the LT1399. The LT1398/LT1399 operate on all ...
The LT1399 and LT1399HV contain three independent 300MHz Current Feedback Amplifiers each with a shutdown pin. The LT1399HV is a higher voltage version of the LT1399. The LT1398 is a two amplifier version of the LT1399. The LT1398/LT1399 operate on all ...
