The L292 is a monolithic LSI circuit in 15-lead Mul-
,
tiwatt package. It is intended for use, together
with L290 and L291, as a complete 3-chip motor
positioning system for applications such as car-
riage/daisy-wheel position control in type-writes. ...
The I.C. L6201, L6202, L6203 is a full bridge driver for motor control ap-
plications realized in Multipower-BCD technology
which combines isolated DMOS power transistors
with CMOS and Bipolar circuits on the same chip.
By using mixed technology it has ...
The OM9375 is one of a series of versatile, integrated three-phase brushless DC motor
controller/driver subsystems housed in a 43 pin power flatpack. The OM9375 is best used as a two
quadrant speed controller for controlling/driving fans, pumps, and motors ...
The OMC506 is an integrated, high density, three phase
Brushless DC (BLDC) motor, speed controller housed in a
MP-3Tpackage. The OMC506 contains the power, driver
and control electronics to adjust timing functions and speed
control loop parameters to ...
The OMC506 is an integrated, high density, three phase
Brushless DC (BLDC) motor, speed controller housed in a
MP-3Tpackage. The OMC506 contains the power, driver
and control electronics to adjust timing functions and speed
control loop parameters to ...
The OM9371 is one of a series of versatile, integrated three-phase brushless DC motor
controller/driver subsystems housed in a 43 pin power flatpack. The OM9371 is best used as a two
quadrant speed controller for controlling/driving fans, pumps, and motors ...
The OM9373 is one of a series of versatile, integrated
three-phase brushless DC motor controller/driver
subsystems housed in a 43 pin power flatpack. The
OM9373 is best used as a two quadrant speed
controller for controlling/driving fans, pumps, ...
The TPD4104AK is a DC brush less motor driver using high
voltage PWM control. It is fabricated by high voltage SOI process.
It contains level shift high-side driver, low-side driver, IGBT
outputs, FRDs and protective functions for under voltage ...
The TPD4104K is a DC brush less motor driver using high
voltage PWM control. It is fabricated by high voltage SOI process.
It contains level shift high side driver, low side driver, IGBT
outputs, FRDs and protective functions for over current and
under ...
The TPD4111K is a DC brushless motor driver using
high-voltage PWM control. It is fabricated using a high-voltage
SOI process.
The device contains a bootstrap circuit, PWM circuit, 3-phase
decode logic, level shift high-side driver, low-side driver, ...
The TPD4112K is a DC brushless motor driver using
high-voltage PWM control. It is fabricated using a high-voltage
SOI process.
The device contains a bootstrap circuit, PWM circuit, 3-phase
decode logic, level shift high-side driver, low-side driver, ...
The TPD4113AK is a DC brush less motor driver using
high- voltage PWM control. It is fabricated using a high-voltage
SOI process. The device contains a level shift high side driver,
low side driver, IGBT outputs, FRDs and protective functions for ...
The TPD4113K is a DC brushless motor driver using
high- voltage PWM control. It is fabricated using a high-voltage
SOI process. The device contains a level shift high side driver,
low side driver, IGBT outputs, FRDs and protective functions for ...
The TA7259P, TA7259F/TA7259FG is a 3,phase Bi-directional motor driver IC.
It designed as an output driver for motors in VTR (capstan,
cylinder, and reel), tape deck, floppy disk, and record player
applications.
To detect position, use of a position ...
The TA7712P/TA7712PG and TA7712F/TA7712FG are provided with a stop function, which enables them to stop the motor having
a large inertia like a video disk player in a short time, so that disks can be changed quickly.
To eliminate the need of the frequency ...
The TA7267BP is a Bridge Driver for brushed DC Motor Rotation
control.
Forward Rotation, Reverse Rotation, Stop and Braking
operations are available.
Its designed for Loading and eel Motor driver for VCR and Tape
Deck, and any other consumer and ...
The TA7279P and TA7279AP can control a DC motor in four
modes (forward rotation, reverse rotation, stop, and brake), using
their bridge driver best suited for switching between forward and
reverse rotation.
These ICs can deliver an output current of ...
The TA7288P is a bridge driver that is ideal for normal / reverse
switching.
This circuit offers four modes: normal rotation, reverse rotation,
stop, and brake.
The output current is 1.0 A (AVE.) and 2.0 A (PEAK). TA7288P
has an ideal circuit ...
The TA8429H/TA8429HQ is full-bridge driver IC for brush motor
rotation control that has a current capability of up to 3.0 A (AVE).
Thermal shutdown and short current protection circuits are
provided, and a stand-by function is also available. ...
The TA8440H/ TA8440HQ is a full-bridge driver for selecting the forward
and reverse running of a motor with brushes and can control four
modes: forward, reverse, stop and braking.
The motor driving unit and the control unit have a separate
power supply ...
The TB62300FG is a dual brushed DC motors driver IC
employing a chopper-based forward/reverse full-bridge
mechanism. It controls two brushed DC motors at high precision.
The motor supply voltage is up to 40 V and the VDD supply
voltage is 5.0 V. ...
The TB6549F/TB6549FG, TB6549P/TB6549PG, TB6549HQ is a full-bridge driver IC for DC
motors that uses an LDMOS structure for output transistors.
High-efficiency drive is possible through the use of a MOS
process with low ON-resistance and a PWM drive ...
The TB6552FN/TB6552FNG/TB6552FL/TB6552FLG is a dual-bridge driver IC for DC
motors with output transistors in an LD MOS structure with low
ON-resistance. Two input signals, IN1 and IN2, can chose one of
four modes such as CW, CCW, short brake, and stop ...
The TPD4105AK is a DC brushless motor driver using
high- voltage PWM control. It is fabricated using a high-voltage
SOI process. The device contains a level shift high side driver,
low side driver, IGBT outputs, FRDs and protective functions for ...
The TPD4105K is a DC brushless motor driver using
high-voltage PWM control. It is fabricated using a high-voltage
SOI process. The device contains a level shift high side driver,
low side driver, IGBT outputs, FRDs and protective functions for ...
The TB6548F/ TB6548FG is a three-phase full-wave sensorless controller
for brushless DC motors. The device supports voltage control by
PWM signal input and is capable of PWM type sensorless driving
when used in conjunction with the TA84005F/ TB6548FG . ...
The TB6575FNG provides sensorless commutation and PWM
current control for 3-phase full-wave BLDC motors. It controls
rotation speed by changing a PWM duty cycle by analog voltage. ...
3-Phase Sine-Wave PWM Driver for BLDC Motors , TB6585FG , Sine-wave PWM drive
, Triangular-wave generator
, Hall amplifier
, Lead angle control
, Current limit control input (VRS = 0.5 V (typ.)) ...
The TB6557FLG is a driver IC for driving DC motors. Its
employs LDMOS devices with low ON resistance for output drive
transistors. The TB6557FLG incorporates two constant
current-controlled H-bridge drivers and four voltage-controlled
H-bridge drivers, ...
The TB6558FLG is a dual bridge driver IC for DC motor control
using LDMOS output transistors with low ON-resistance.
Four operation modes are selectable via IN1 and IN2: forward,
reverse, short brake and stop.
The TB6558FLG uses constant-current PWM ...
The TB6559FG is a full-bridge DC motor driver with LDMOS
output transistors.
It uses P-channel MOSFETs on the high side and N-channel
MOSFETs on the low side, eliminating the need for a charge
pump. The TB6559FG achieves high thermal efficiency.
Four ...
The TB6561FG is a dual bridge driver IC for DC brush motor that
contains MOS transistors in an output stage.
By using low ON-resistance MOS transistors and PWM current
control circuitry, the driver achieves high efficiency. ...
The TB6561NG is a dual bridge driver IC for DC brush motor
that contains MOS transistors in an output stage.
By using low ON-resistance MOS transistors and PWM current
control circuitry, the driver achieves high efficiency. ...
The TB6591FLG is a DC motor driver IC using LDMOS output
transistors with low ON-resistance.
The TB6591FLG incorporates one constant-current
PWM-controlled, chopper-type bridge driver, and three
voltage-regulated stepping motor drivers (six bridge ...
The TB6592FL/ TB6592FLG is a dual-bridge driver IC for DC motors
with output transistors in an LD MOS structure with low
ON-resistance. Two input signals, IN1 and IN2, can be used to
select one of four modes such as CW, CCW, short brake, and sto
mode. ...
TB6593FNG is a driver IC for DC motor with output
transistor in LD MOS structure with low ON-resistor. Two
input signals, IN1 and IN2, can choose one of four modes
such as CW, CCW, short brake, and stop mode. ...
The TB6596FLG is a DC motor driver IC using LDMOS output
transistors with low ON-resistance.
The TB6596FLG incorporates one PWM-constant-current
H-bridge driver, four direct-PWM-controlled H-bridge drivers, and
also one linear constant-current H-bridge ...
The TB6607FLG is a DC motor driver IC using LDMOS output
transistors with low ON-resistance.
The TB6607FLG incorporates two PWM-controlled,
constant-current H-bridge drivers and three
direct-PWM-controlled H-bridge drivers. The TB6607FLG is best ...
These 3-phase, full-wave, brushless DC motor driver ICs have
been developed for use in CD-ROM drive spindle motors. The
TA8493F/TA8493FG/TA8493AF/TA8493AFG/ TA8493BF/TA8493BFG contain in its upper stage a
discrete power transistor (P-ch-MOS) and uses ...
The TB6537P/TB6537PG/TB6537F/TB6537FG is a 3-phase full-wave sensorless
controller for brushless DC motors. It is capable of controlling
voltage through PWM signal input. When combined with various
drive circuits, it can be used for various types of ...
TB6612FNG is a driver IC for DC motor with output
transistor in LD MOS structure with low ON-resistor. Two
input signals, IN1 and IN2, can choose one of four modes
such as CW, CCW, short brake, and stop mode. ...
The A3989 is designed operate at voltages up to 36 V while driving
one bipolar stepper motor, at currents up to 1.2 A, and one dc motor,
at currents up to 2.4 A. The A3989 includes a fixed off-time pulse
width modulation (PWM) regulator for current control. ...
The A8904 is a 3-phase brushless DC motor controller/driver designed
for applications where accurate control of high-speed motors is required.
The three half-bridge outputs are low on-resistance, N-channel DMOS
devices capable of driving up to 1.2 A. The ...
KIA6801K is a monolithic integrated circuit designed for
driving bi-directional DC motor with braking and speed control,
and suitable for the loading motor driver of VCR, Cassette tape
recorders systems. The speed control can be achieved by ...
The NJM2642 is a 2-phase DC brushless motor pre-driver IC. It incorporates Lock Detect / Auto Protection Circuit and totem-pole pre- drivers for external power MOS-FET. The turn ON/ turn OFF ratio at Auto Protection Release was set in 1:10 easy-to-use. Two ...
The NJM2644 is a 2-phase DC brushless motor pre-driver IC. It incorporates Lock Detect and Auto Protection circuit for safety operation. Especially1:10 ON/OFF duty ratio while motor is locked reduces heat generation in motor windings. Moreoverthe pin is ...
The NJM2646 is a 2-phase DC brushless motor pre-driver IC.It incorporates Lock Detect / Auto Protection Circuit and totem-pole pre-driver for external power MOS-FET.The turn ON / turn OFF ratio at Auto Protection Releasewas set in 1:10 easy-to-use.Moreover, ...
The NJU7325 is a dual power amplifier. It features MOS-FET output for better saturation characteristics. It is suitable for small fan-motor applications. ...
The NJU7326 is a single-phase DC brushless motor driver IC. It features MOS-FET output for better saturation characteristics. Slew rate of amplifiers and feedback resistors are optimized to achieve low-noise motor operation. It is suitable for small fan-motor ...
The NJU7327 is a single-phase DC brushless motor driver IC for small fan-motor and high power applications. It features MOS-FET driver circuit for better saturation characteristics. Slew late of amplifiers and feedback resistors are optimized to achieve ...
The NJU7329B is a single-phase DC brushless motor driver IC for small fan-motor and high power applications. It features MOS-FET driver circuit for better saturation characteristics. Slew late of amplifiers and feedback resistors are optimized to achieve ...
The NJU7332 is a single-phase DC brushless motor driver IC for very small fan-motor application. It features MOS-FET driver circuit for better saturation characteristics. Slew late of amplifiers and feedback resistors are optimized to achieve low-noise motor ...
The NJU7333 is a single-phase DC brushless motor driver IC for small fan-motor and high power applications. It features MOS-FET driver circuit for better saturation characteristics. Slew late of amplifiers and feedback resistors are optimized to achieve ...
The NJU7342 is a single-phase DC brushless motor driver IC for small fan-motor applications. It features MOS-FET driver circuit for better saturation characteristics. Slew late of amplifiers and feedback resistors are optimized to achieve low-noise motor ...
The NJU7343/ NJU7344 / NJU7345 is a single-phase DC brushlessmotor driver IC developed for a small fan motor. Adoptingthe CMOS process, it can provide a low saturation output voltage that is effective in high current conditions.This driver includes Lock ...
The NJM2624A is a 3-phase brushless DC motor pre-driver which requires external power-transistors suited to drive current of the motor. The Run Enable function is used as PWM control besides of ON/OFF switched function. ...
The NJM2625A is a 3 phase DC brush-less motor driver IC with PWM control. It incorporates hall amplifiersPWM control circuitstotem-pole pre drivers for external power MOS transistors. current limit and frequency generator circuit. The NJM2625A easily ...
The NJM2626 is a 3-phase DC brush less motor control pre-driver IC with PWM control. It takes hall IC inputs and generates motor driving waveform. Output pre-driver is optimized to work with external power MOS transistors for better power handling. The ...
The NJM2627 is a 3-phase DC brush less motor control pre-driver IC.Output pre-driver is optimized to work with external power MOS FET for better power handling.The NJM2627 can easily implement speed control by input of PWM signal to ON/ OFF terminal. ...
The NJW4302 is a three-phase DC brushless motor pre-driver IC for precision applications. The NJW4302 consists of PWM drivermotor velocity controlFG(Frequency Generator) outputand voltage velocity integration circuit. The NJW4302 realizes stabilized velocity ...
The NJM2606/ NJM2606A are integrated circuits with wide operating supply voltage range for DC motor speed control. Especiallythe NJM2606A is suited for the applications requiring low staturation output voltage. ...
The NJM2611 is an integrated circuit to be applied on servo motor of radio controlled operation. Wide range of operating voltageand the NJM2611 has the feature of internal circuit of maintaining constant voltage which helps stabilizing from fluctuation caused ...
The ZXBM1017 is a Single-Phase, DC brushless motor pre-driver with PWM variable speed control and current limit features suitable for fans, blowers and pump motors. Where the system dictates, this device can be controlled via an external voltage, PWM signal or ...
The ZXBM2004 is a two-phase, DC brushless motor pre-driver with PWM variable speed control suitable for fan and blower motors. The controller is intended for applications where the fan or blower speed is controlled by an external PWM signal, thermistor or DC ...
SA1510 is a monolithic integrated circuit designed for the rotating speed
control and DC motor driver. SA1510 adopts bridge driver circuit which
have two output port, used for drive positive and inverse direction of
motor, the peak value of the ...
The UTC A9849 is ICs developed for CD-ROM
spindle motor drives. These ICs possess a short brake
and reverserotation brake for two types of brake
functions, and also contain FG output and rotation
direction detection (FR) circuits,making them ...
The UTC AN6651 is a monolithic integrated circuit designed
for the rotating control of a compact DC motor which is used for a
tape recorder, recorder player etc. ...
The UTC BA6208 is designed for driving reversible motor use, it
contain a logic section to controls forward and reverse rotations as
well as forced stop, and an output power section is able to supply an
output current of up to 100mA (typical) according ...
The FAN8082 is a monolithic integrated circuit designed for
driving bi-directional DC motor with braking and speed con-
trol, and it is suitable for the loading motor driver of VCR,
CDP, and TOY systems. The speed control can be achieved
by adjusting ...