Fabricated in 0.5 micron CMOS technology, the GC2011A chip is a general purpose digital filter chip with 32 multiply-add filter cells. The chip operates at rates up to 106 MHz. The input data size is 12 bits and the coefficient data size is 14 bits. The output ...
The UAF42 is a universal active filter that can be configured for a wide range of low-pass, high-pass, and band-pass Filters It uses a classic state-variable analog architecture with an inverting amplifier and two integrators. The integrators include on-chip ...
The LMF100 consists of two independent general purpose high performance switched capacitor Filters With an external clock and 2 to 4 resistors, various second-order and first-order filtering functions can be realized by each filter block. Each block has 3 ...
The MF10 consists of 2 independent and extremely easy to use, general purpose CMOS active filter building blocks. Each block, together with an external clock and 3 to 4 resistors, can produce various 2nd order functions. Each building block has 3 output pins. ...
The Serial I/O Filter HSP43124 is a high performance filter engine that is ideal for off loading the burden of filter processing from a DSP microprocessor. It supports a variety of multistage filter configurations based on a user programmable filter and fixed ...
The HSP43168 Dual FIR Filter consists of two independent 8-tap FIR Filters Each filter supports decimation from 1 to 16 and provides on-board storage for 32 sets of coefficients. The Block Diagram shows two FIR cells each fed by a separate coefficient bank ...
The HSP43216 Halfband Filter addresses a wide variety of applications by combining fS/4 (fS = sample frequency) quadrature up/down convert circuitry with a fixed coefficient halfband filter processor as shown in the block diagram. These elements may be ...
The HSP43220 Decimating Digital Filter is a linear phase
low pass decimation filter which is optimized for filtering
narrow band signals in a broad spectrum of a signal
processing applications. The HSP43220 offers a single chip
solution to signal ...
The TDA9181 is a an adaptive PAL/NTSC comb filter with two internal delay lines, Filters clock control and input clamps. Video standards PAL B, G, H, D, I, M and N and NTSC M are supported.Two CVBS input signals can be selected by means of an input switch.The ...
The TDA9183 is a an adaptive NTSC comb filter with two
internal delay lines, Filters clock control and input clamps.
The NTSC M video standard is supported.
Two CVBS input signals can be selected by means of an
input switch.
The selected CVBS input ...
The LT6600-10 combines a fully differential amplifier with a 4th order 10MHz lowpass filter approximating a Chebyshev frequency response. Most differential amplifiers require many precision external components to tailor gain and bandwidth. In contrast, with ...
The LT6600-15 combines a fully differential amplifier with a 4th order 15MHz lowpass filter approximating a Chebyshev frequency response. Most differential amplifiers require many precision external components to tailor gain and bandwidth. In contrast, with ...
The LT6600-2.5 combines a fully differential amplifier with a 4th order 2.5MHz lowpass filter approximating a Chebyshev frequency response. Most differential amplifiers require many precision external components to tailor gain and bandwidth. In contrast, with ...
The LT6600-20 combines a fully differential amplifier with a 4th order 20MHz lowpass filter approximating a Chebyshev frequency response. Most differential amplifiers require many precision external components to tailor gain and bandwidth. In contrast, with ...
The LT6600-5 combines a fully differential amplifier with a 4th order 5MHz lowpass filter approximating a Chebyshev frequency response. Most differential amplifiers require many precision external components to tailor gain and bandwidth. In contrast, with the ...
The LT1567 is an analog building block optimized for very low noise high frequency filter applications. It contains two wideband rail-to-rail operational amplifiers, one of them internally configured as a unity-gain inverter. With the addition of a few passive ...
The LT1568 is an easy-to-use, active-RC filter building block with rail-to-rail inputs and outputs. The internal capacitors of the IC and the GBW product of the internal low noise op amps are trimmed such that consistent and repeatable filter responses can be ...
The LTC1059 consists of a general purpose, high performance, active filter building block and an uncommitted op amp. The filter building block together with an external clock and 2 to 5 resistors can produce various 2nd order functions which are available at ...
The LTC1060 consists of two high performance, switched capacitor Filters Each filter, together with 2 to 5 resistors, can produce various 2nd order filter functions such as lowpass, bandpass, highpass notch and allpass. The center frequency of these functions ...
The LTC1061 consists of three high performance, universal filter building blocks. Each filter building block together with an external clock and 2 to 5 resistors can produce various second order functions which are available at its three output pins. Two out ...
The LTC1062 is a 5th order all pole maximally flat lowpass filter with no DC error. Its unusual architecture puts the filter outside the DC path so DC offset and low frequency noise problems are eliminated. This makes the LTC1062 very useful for lowpass ...
The filter cutoff frequency is controlled either by an internal or external clock.The clock-to-cut off frequency ratio is 100:1. The on-board clock is power supply independent, and it is programmed via an external RC. The 50VRMS clock feed through is ...
The LTC1064 consists of four high speed, low noise switched-capacitor filter building blocks. Each filter building block, together with an external clock and three to five resistors can provide various 2nd order functions like lowpass, highpass, bandpass and ...
59e
The LTC1064-1 is an 8th order, clock sweepable elliptic (Cauer) lowpass switched capacitor filter. The passband ripple is typically 0.15dB, and the stopband attenuation at 1.5 times the cutoff frequency is 68dB or more. An external TTL or CMOS clock ...
The LTC1064-2 is a monolithic 8th order lowpass Butterworth filter, which provides a maximally flat passband. The attenuation slope is ,48dB/octave and the maximum attenuation is in excess of 80dB. An external
591
TTL or CMOS clock programs the filter,s ...
The LTC1064-3 is a monolithic 8th order lowpass Bessel filter, which provi
502
des a linear phase response over its entire passband. An external TTL or CMOS clock programs the filter,s cutoff frequency. The clock to cutoff frequency ratio is 75:1 (Pin 10 at ...
,
The LTC 1064-4 is an 8th order, clock sweepable Cauer
lowpass switched capacitor filter. An external TTL or
CMOS clock programs the value of the Filters cutof
+
frequency. With Pin 10 at V , the f to f ratio is
CLK CUTOFF
50:1; the filter has a ...
The LTC1064-7 features wide dynamic range. With single 5V supply, the S/N + THD is 76dB. Optimum 92dB S/N is obtained with 7.5V supplies. The clock-to-cutoff frequency ratio of the LTC1064-7 can be set to 50:1 (pin 10 to V + ) or 100:1 (pin 10 to V - ).
The LTC1065 is the first monolithic filter providing both clock-tunability with low DC output offset and over 12-bit DC accuracy. The frequency response of the LTC1065 closely approximates a 5th order Bessel polynomial. With appropriate PCB layout techniques ...
The LTC1066-1 is an 8th order elliptic lowpass filter which simultaneously provides clock-tunability and DC accuracy. The unique and proprietary architecture of the filter allows 14 bits of DC gain linearity and a maximum of 1.5mV DC offset. An external RC is ...
The LTC1067/LTC1067-50 consist of two identical rail-to-rail, high accuracy and very wide dynamic range 2nd order switched-capacitor building blocks. Each building block, together with three to five resistors, provides 2nd order filter functions such as ...
The LTC1067/LTC1067-50 consist of two identical rail-to-rail, high accuracy and very wide dynamic range 2nd order switched-capacitor building blocks. Each building block, together with three to five resistors, provides 2nd order filter functions such as ...
The LTC1068 product family consists of four monolithic clock-tunable filter building blocks. Each product contains four matched, low noise, high accuracy 2nd order switched-capacitor filter sections. An external clock tunes the center frequency of each 2nd ...
The LTC1068 product family consists of four monolithic clock-tunable filter building blocks. Each product contains four matched, low noise, high accuracy 2nd order switched-capacitor filter sections. An external clock tune
559
s the center frequency of each ...
The LTC1068 product family consists of four monolithic clock-tunable filter building blocks. Each product contains four matched, low noise, high accuracy 2nd order switched-capacitor filter sections. An external clock tunes the center frequency of each 2nd ...
The LTC1068 product family consists of four monolithic clock-tunable filter building blocks. Each product contains four matched, low noise, high accuracy 2nd order switched-capacitor filter sections. An external clock tunes the center frequency of each 2nd ...
The LTC1069-1 is a monolithic 8th order lowpass filter featuring clock-tunable cutoff frequency and 2.5mA power supply current with a single 5V supply. An additional feature of the LTC1069-1 is operation with a single 3.3V supply. The cutoff frequency ...
The LTC1069-6 is a monolithic low power, 8th order lowpass filter optimized for single 3V or single 5V supply operation. The LTC1069-6 typically consumes 1mA under single 3V supply operation and 1.2mA under 5V operation. The cutoff frequency of the ...
The LTC1069-7 is a monolithic, clock-tunable, linear phase, 8th order lowpass filter. The amplitude response of the filter approximates a raised cosine filter with an alpha of one. The gain at the cutoff frequency is ,3dB and the attenuation at twice the ...
The LTC1164 consists of four low power, low noise 2nd order switched capacitor filter building blocks. Each building block typically consumes 850A supply current. Low power is achieved without sacrificing noise and distortion. Each building block, together ...
Low power operation is achieved without compromising noise or distortion performance. With 5V supplies and 10kHz cutoff frequency, the operating signal-to-noise ratio is 86dB and the THD throughout the passband is 0.015%. Under the same conditions, a 77dB ...
The LTC1164-6 is a monolithic 8th order elliptic lowpass filter featuring clock-tunable cutoff frequency and low power supply current. Low power operation is achieved without compromising noise or distortion performance. At 5V supplies the LTC1164-6 uses only ...
Low power is achieved without sacrificing dynamic range. With single 5V supply, the S/N + THD is up to 75dB. Optimum 91dB S/N is obtained with 7.5V supplies. The clock-to-cutoff frequency ratio of the LTC1164-7 can be set to 50:1 (pin 10 to V + ) or 100:1 ...
The aliasing performance of the LTC1264 is improved by double-sampling each 2nd order section. Input signal frequencies can reach up to twice the clock frequency before any alias products will be detectable. For Q A customized monolithic version of the ...
The LTC1264-7 is a clock-tunable monolithic 8th order lowpass filter with linear passband phase and flat group delay. The amplitude response approximates a maximally flat passband and exhibits steeper roll-off than an equivalent 8th order Bessel filter. For ...
The LTC1560-1 is a 5th order, continuous-time, lowpass filter. The elliptic transfer function of the LTC1560-1 was carefully chosen to reach a compromise between selectivity, for antialiasing applications, and transient response. The filter cutoff frequency, ...
The LTC1562 is a low noise, low distortion continuous-time filter with rail-to-rail inputs and outputs, optimized for a center frequency (fO) of 10kHz to 150kHz. Unlike most monolithic Filters no clock is needed. Four independent 2nd order filter blocks can ...
The LTC1562-2 is a low noise, low distortion continuous time filter with rail-to-rail inputs and outputs, optimized for a center frequency (fO) of 20kHz to 300kHz. Unlike most monolithic Filters no clock is needed. Four independent 2nd order filter blocks can ...
The LTC1563-2/LTC1563-3 are a family of extremely easy-to-use, active RC lowpass Filters with rail-to-rail inputs and outputs and low DC offset suitable for systems with a resolution of up to 16 bits. The LTC1563-2, with a single resistor value, gives a ...
The LTC1563-2/LTC1563-3 are a family of extremely easy-to-use, active RC lowpass Filters with rail-to-rail inputs and outputs and low DC offset suitable for systems with a resolution of up to 16 bits. The LTC1563-2, with a single resistor value, gives a ...
The LTC1565-31 is a 7th order, continuous time, linear phase lowpass filter. The selectivity of the LTC1565-31, combined with its linear phase and dynamic range, make it suitable for filtering in data communications or data acquisition systems. The filter ...
The LTC1566-1 is a 7th order continuous time lowpass filter with 12dB of passband gain. The selectivity, linearity and dynamic range makes the LTC1566-1 suitable for filtering in data communications or data acquisition systems. The filter attenuation is 40dB ...
The LTC1569-6 is a 10th order lowpass filter featuring linear phase and a root raised cosine amplitude response. The high selectivity of the LTC1569-6 combined with its linear phase in the passband makes it suitable for filtering both in data communications ...
The LTC1569-7 is a 10th order lowpass filter featuring linear phase and a root raised cosine amplitude response. The high selectivity of the LTC1569-7 combined with its linear phase in the passband makes it suitable for filtering both in data communications ...
The LTC6602 is a dual, matched, programmable bandpass or lowpass lter and differential driver. The selectivity of the LTC6602, combined with its linear phase, phase matching and dynamic range, make it ideal for ltering in RFID systems. With one degree phase ...
The MAX291/MAX292/MAX295/MAX296 are easy-to-use, 8th-order, lowpass, switched-capacitor Filters that can be set up with corner frequencies from 0.1Hz to 25kHz (MAX291/MAX292) or 0.1Hz to 50kHz (MAX295/MAX296). The MAX291/MAX295 Butterworth Filters provide ...
The MAX291/MAX292/MAX295/MAX296 are easy-to-use, 8th-order, lowpass, switched-capacitor Filters that can be set up with corner frequencies from 0.1Hz to 25kHz (MAX291/MAX292) or 0.1Hz to 50kHz (MAX295/MAX296). The MAX291/MAX295 Butterworth Filters provide ...
The MAX291/MAX292/MAX295/MAX296 are easy-to-use, 8th-order, lowpass, switched-capacitor Filters that can be set up with corner frequencies from 0.1Hz to 25kHz (MAX291/MAX292) or 0.1Hz to 50kHz (MAX295/MAX296). The MAX291/MAX295 Butterworth Filters provide ...
The MAX291/MAX292/MAX295/MAX296 are easy-to-use, 8th-order, lowpass, switched-capacitor Filters that can be set up with corner frequencies from 0.1Hz to 25kHz (MAX291/MAX292) or 0.1Hz to 50kHz (MAX295/MAX296). The MAX291/MAX295 Butterworth Filters provide ...
The MAX274 and MAX275 are
643
continuous-time active Filters consisting of independent cascadable 2nd-order sections. Each section can implement and all-pole bandpass or lowpass filter response, such as Butterworth, Bessel, Chebyshev, and is programmed by ...
The MAX274 and MAX275 are
643
continuous-time active Filters consisting of independent cascadable 2nd-order sections. Each section can implement and all-pole bandpass or lowpass filter response, such as Butterworth, Bessel, Chebyshev, and is programmed by ...
The MAX260/MAX261/MAX262 CMOS dual second-order universal switched-capacitor active Filters allow microprocessor control of precise filter functions. No external components are required for a variety of bandpass, lowpass, highpass, notch, and allpass ...
The MAX260/MAX261/MAX262 CMOS dual second-order universal switched-capacitor active Filters allow microprocessor control of precise filter functions. No external components are required for a variety of bandpass, lowpass, highpass, notch, and allpass ...
The MAX260/MAX261/MAX262 CMOS dual second-order universal switched-capacitor active Filters allow microprocessor control of precise filter functions. No external components are required for a variety of bandpass, lowpass, highpass, notch, and allpass ...
The MAX7408/MAX7411/MAX7412/MAX7415 5th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7408/MAX7411) or +3V (MAX7412/MAX7415) supply. The devices draw only 1.2mA of supply current and all
700
ow corner frequencies ...
The MAX7408/MAX7411/MAX7412/MAX7415 5th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7408/MAX7411) or +3V (MAX7412/MAX7415) supply. The devices draw only 1.2mA of supply current and all
700
ow corner frequencies ...
The MAX7408/MAX7411/MAX7412/MAX7415 5th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7408/MAX7411) or +3V (MAX7412/MAX7415) supply. The devices draw only 1.2mA of supply current and all
700
ow corner frequencies ...
The MAX7408/MAX7411/MAX7412/MAX7415 5th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7408/MAX7411) or +3V (MAX7412/MAX7415) supply. The devices draw only 1.2mA of supply current and all
700
ow corner frequencies ...
The MAX7409/MAX7410/MAX7413/MAX7414 5th-order, lowpass, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7409/MAX7410) or +3V (MAX7413/
MAX7414) supply. These devices draw only 1.2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7409/MAX7410/MAX7413/MAX7414 5th-order, lowpass, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7409/MAX7410) or +3V (MAX7413/
MAX7414) supply. These devices draw only 1.2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7409/MAX7410/MAX7413/MAX7414 5th-order, lowpass, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7409/MAX7410) or +3V (MAX7413/
MAX7414) supply. These devices draw only 1.2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7409/MAX7410/MAX7413/MAX7414 5th-order, lowpass, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7409/MAX7410) or +3V (MAX7413/
MAX7414) supply. These devices draw only 1.2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7400/MAX7403/MAX7404/MAX7407 8th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7400/MAX7403) or +3V (MAX7404/MAX7407) supply. These devices draw 2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7400/MAX7403/MAX7404/MAX7407 8th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7400/MAX7403) or +3V (MAX7404/MAX7407) supply. These devices draw 2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7400/MAX7403/MAX7404/MAX7407 8th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7400/MAX7403) or +3V (MAX7404/MAX7407) supply. These devices draw 2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7400/MAX7403/MAX7404/MAX7407 8th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7400/MAX7403) or +3V (MAX7404/MAX7407) supply. These devices draw 2mA of supply current and allow corner frequencies from 1Hz to ...
The MAX7401/MAX7405 8th-order, lowpass, Bessel, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7401) or +3V (MAX7405) supply. These devices draw only 2mA of supply current and allow corner frequencies from 1Hz to 5kHz, making them ideal for ...
The MAX7401/MAX7405 8th-order, lowpass, Bessel, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7401) or +3V (MAX7405) supply. These devices draw only 2mA of supply current and allow corner frequencies from 1Hz to 5kHz, making them ideal for ...
The MAX7480 8th-order, lowpass, Butterworth, switched-capacitor filter (SCF) operates from a single +5V supply. The device draws only 2.9mA of supply current and allows corner frequencies from 1Hz to 2kHz, making it ideal for low-power post-DAC filtering and ...
The MAX7426/MAX7427 5th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7426) or +3V (MAX7427) supply. The devices draw only 0.8mA of supply current and allow corner frequencies from 1Hz to 12kHz, making them ideal for ...
The MAX7426/MAX7427 5th-order, lowpass, elliptic, switched-capacitor Filters (SCFs) operate from a single +5V (MAX7426) or +3V (MAX7427) supply. The devices draw only 0.8mA of supply current and allow corner frequencies from 1Hz to 12kHz, making them ideal for ...
The MAX7490/MAX7491 consist of two identical low-power, low-voltage, wide dynamic range, Rail-to-Rail, 2nd-order switched-capacitor building blocks. Each of the two filter sections, together with two to four external resistors, can generate all standard ...
The MAX7490/MAX7491 consist of two identical low-power, low-voltage, wide dynamic range, Rail-to-Rail, 2nd-order switched-capacitor building blocks. Each of the two filter sections, together with two to four external resistors, can generate all standard ...