ARINC 429 Bus Interface Line Driver Circuit

The HS-3182 is a monolithic dielectrically isolated bipolar differential Line Driver designed to meet the specifications of ARINC 429. This Device is intended to be used with a companion chip, HS-3282 CMOS ARINC Bus Interface Circuit, which provides the data formatting and processor Interface function.
All Logic inputs are TTL and CMOS compatible. In addition to the DATA (A) and DATA (B) inputs, there are also inputs for Clock and SYNC signals which are ANDd with the DATA inputs. This feature enhances system performance and allows the HS-3182 to be used with devices other than the HS-3182.
Three power supplies are necessary to operate the HS-3182 +V = +15V 10%, -V = -15V 10%, and V1 = 5V 5%. VREF is used to program the differential output voltage swing such that VOUT (DIFF) = 2VREF. Typically, VREF = V1 = 5V 5%, but a separate power supply may be used for VREF which should not exceed 6V.
The driver output impedance is 75 20% at +25C. Driver output rise and fall times are independently programmed through the use of two external capacitors connected to the CA and CB inputs. Typical capacitor values are CA = CB = 75pF for high-speed operation (100kBPS), and CA = CB = 300pF for low-speed operation (12kBPS to 14.5kBPS). The outputs are protected against overvoltage and short circuit as shown in the Block Diagram. The HS-3182 is designed to operate over an ambient temperature range of -55C to +125C, or -40C to +85C.
By Intersil Corporation
Part Manufacturer Description Datasheet Samples
4HS4-118 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 0.5 A at 125 Vac, Integral Lever Actuator, Leadwire Termination
4HS9-118 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Normally Open Circuitry, 15 A at 28 Vdc, Integral Lever Actuator, Leadwire Termination
102HS1 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 1 A at 125 Vac, Integral Lever Actuator, Screw Termination
1HS3 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 1 A at 115 Vac, Roller Lever Actuator, Screw Termination
4HS4-318 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 0.5 A at 125 Vac, Integral Lever Actuator, Leadwire Termination
4HS4-918 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 0.5 A at 125 Vac, Integral Lever Actuator, Leadwire Termination
4HS4-620 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 0.5 A at 125 Vac, Integral Lever Actuator, Leadwire Termination
1HS6 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 1 A at 115 Vac, Integral Lever Actuator, Screw Termination, Military Part Number MS25011-4
1HS1 Honeywell Sensing and Control HS Series Hermetically Sealed Basic Switch, Single Pole Double Throw Circuitry, 1 A at 115 Vac, Integral Lever Actuator, Screw Termination, Military Part Number MS25011-1
36CX1 Honeywell Sensing and Control Explosion-Proof Limit Switches Series CX: Short Housing: Top Plunger; 1NC 1NO SPDT Snap Action; Number of internal basic switches HS: 1; 0.75 in - 14NPT conduit
HS-3182 's PackagesHS-3182 's pdf datasheet
5962-8687901EA
HS1-3182-8 DIP
HS1-3182-9- DIP
HS4-3182-8 CLCC

HS-3182 pdf datasheet download


HS-3182 Pinout, Pinouts
HS-3182 pinout,Pin out
This is one package pinout of HS-3182,If you need more pinouts please download HS-3182's pdf datasheet.

HS-3182 Application circuits
HS-3182 circuits
This is one application circuit of HS-3182,If you need more circuits,please download HS-3182's pdf datasheet.


Related Electronics Part Number

Related Keywords:

HS-3182 Pb-Free HS-3182 Cross Reference HS-3182 Schematic HS-3182 Distributor
HS-3182 Application Notes HS-3182 RoHS HS-3182 Circuits HS-3182 footprint