Dot/Bar Display Driver

The LM3914 is a monolithic integrated circuit that senses Analog voltage levels and drives 10 LEDs providing a linear Analog Display A single pin changes the Display from a moving dot to a bar graph. Current drive to the LEDs is regulated and programmable, eliminating the need for resistors. This feature is one that allows operation of the whole system from less than 3V.
The circuit contains its own adjustable reference and accurate 10-step voltage divider. The low-bias-current input Buffer accepts signals down to ground, or V-, yet needs no protection against inputs of 35V above or below ground. The Buffer drives 10 individual Comparators referenced to the precision divider. Indication non-linearity CAN thus be held typically to %, even over a wide temperature range.
Versatility was designed into the LM3914 so that controller, visual alarm, and expanded scale functions are easily added on to the Display system. The circuit CAN drive LEDs of many colors, or low-current incandescent lamps. Many LM3914 CAN be "chained" to form Displays of 20 to over 100 segments. Both ends of the voltage divider are externally available so that 2 drivers CAN be made into a zero-center meter.
The LM3914 is very easy to apply as an Analog meter circuit. A 1.2V full-scale meter requires only 1 resistor and a single 3V to 15V supply in addition to the 10 Display LEDs If the 1 resistor is a pot, it becomes the LED brightness control. The simplified block diagram illustrates this extremely simple external circuitry.
When in the dot mode, there is a small amount of overlap or "fade" (about 1 mV) between segments. This assures that at no time will all LEDs be "OFF", and thus any ambiguous Display is avoided. Various novel Displays are possible.
Much of the Display flexibility derives from the fact that all outputs are individual, DC regulated currents. Various effects CAN be achieved by modulating these currents. The individual outputs CAN drive a Transistor as well as a LED at the same time, so controller functions including "staging" control CAN be performed. The LM3914 CAN also act as a programmer, or Sequencer
The LM3914 is rated for operation from 0C to +70C. The LM3914N-1 is available in an 18-lead molded (N) package.
The following typical application illustrates adjusting of the reference to a desired value, and proper grounding for accurate operation, and avoiding oscillations.
By National Semiconductor Corporation
Part Manufacturer Description Datasheet Samples
LM3914VX/NOPB Texas Instruments IC LED DISPLAY DRIVER, PQCC20, PLASTIC, LCC-20, Display Driver
LM3914VX Texas Instruments IC LED DISPLAY DRIVER, PQCC20, PLASTIC, LCC-20, Display Driver
LM3914N-1/NOPB Texas Instruments IC LED DISPLAY DRIVER, PDIP18, PLASTIC, DIP-18, Display Driver
LM3914V Texas Instruments IC LED DISPLAY DRIVER, PQCC20, PLASTIC, LCC-20, Display Driver
LM3914N-1 Texas Instruments Dot/Bar Display Driver 18-PDIP 0 to 70
LM3914V/NOPB Texas Instruments IC LED DISPLAY DRIVER, PQCC20, PLASTIC, LCC-20, Display Driver
LM3914 's PackagesLM3914 's pdf datasheet
LM3914N-1 DIP
LM3914V PLCC
LM3914VX PLCC
LM3914-MDC

LM3914 pdf datasheet download


LM3914 Pinout, Pinouts
LM3914 pinout,Pin out
This is one package pinout of LM3914,If you need more pinouts please download LM3914's pdf datasheet.

LM3914 Application circuits
LM3914 circuits
This is one application circuit of LM3914,If you need more circuits,please download LM3914's pdf datasheet.


Related Electronics Part Number

Related Keywords:

LM3914 Pb-Free LM3914 Cross Reference LM3914 Schematic LM3914 Distributor
LM3914 Application Notes LM3914 RoHS LM3914 Circuits LM3914 footprint