This 9-bit to 18-bit D-type latch is designed for 3.15-V to 3.45-V VCC operation. The D inputs accept HSTL levels and the Q outputs provide LVTTL levels. The SN74HSTL16918 is particularly suitable for driving an address bus to two banks of memory. Each ...
This 9-bit to 18-bit D-type latch is designed for 3.15-V to 3.45-V VCC operation. The D inputs accept HSTL levels and the Q outputs provide LVTTL levels. The SN74HSTL16919 is particularly suitable for driving an address bus to two banks of memory. Each ...
This 20-bit universal bus driver is designed for 3-V to 3.6-V VCC operation and SSTL_3 or LVTTL I/O levels. Data flow from A to Y is controlled by the output-enable (OE) input. The device operates in the transparent mode when latch enable (LE) is high. ...
CD4089B is a low-power 4-bit digital rate multiplier that provides an output pulse rate that is the clock-input-pulse rate multiplied by 1/16 times the binary input. For example, when the binary input number is 13, there will be 13 output pulses for every 16 ...
CD4521B consists of an oscillator section and 24 ripple-carry binary counter stages. The oscillator configuration (using IN1) allows design of either RC or crystal oscillator circuits. IN1 should be tied either HIGH or LOW when not in use. A HIGH on the ...
CD4527B is a low-power 4-bit digital rate multiplier that provides an output-pulse rate which is the clock-input-pulse rate multiplied by 1/10 times the BCD input. For example, when the BCD input is 8, there will be 8 output pulses for every 10 input pulses. ...
These monolithic, fully synchronous, programmable counters utilize Series 54/74 TTL circuitry to achieve 32-megahertz typical maximum operating frequencies. These six-bit serial binary counters feature buffered clock, clear, and enable inputs to control the ...
These programmable frequency dividers/digital timers contain 31 flip-flops plus 30 gates (\'LS292) or 15 flip-flops plus 29 gates (\'LS294) on a single chip. The count modulo is under digital control of the inputs provided. Both types feature an ...
CD40117B is a dual 4-bit terminator that can be programmed by means of STROBE and DATA control bits to function as pull-up or pull-down resistors. The CD40117B can also be programmed to function as latches to terminate any open or unused CMOS Logic when used ...
This device is designed to terminate bus lines in CMOS systems. The integrated low-impedance diodes clamp the voltage of undershoots and overshoots caused by line reflections and ensure signal integrity. The device also contains a bus-hold function that ...
This device is designed to terminate bus lines in CMOS systems. The integrated low-impedance diodes clamp the voltage of undershoots and overshoots caused by line reflections and ensure signal integrity. The device also contains a bus-hold function that ...
This bus-termination array is designed to reduce reflection noise and minimize ringing on high-performance bus lines. The SN74F1016 features a 16-bit R-C network and Schottky barrier diode array. These Schottky diodes provide clamp-to-ground functionality and ...
This Schottky barrier diode bus-termination array is designed to reduce reflection noise on memory bus lines. This device consists of an 8-bit high-speed Schottky diode array suitable for a clamp to GND. The SN74F1056 is characterized for operation from ...
This Schottky barrier diode bus-termination array is designed to reduce reflection noise on memory bus lines. This devcie consists of a 12-bit high-speed Schottky diode array suitable for a clamp to GND. The SN74S1050 is characterized for operation from ...
This Schottky barrier diode SN74S1051 bus-termination array is designed to reduce reflection noise on memory bus lines. This device consists of a 12-bit high-speed Schottky diode array suitable for clamping to VCC and/or GND. ...
This Schottky barrier diode bus-termination array is designed to reduce reflection noise on memory bus lines. This device consists of a 16-bit high-speed Schottky diode array suitable for a clamp to GND. The SN741052 is characterized for operation from 0C ...
This Schottky barrier diode bus-termination array is designed to reduce reflection noise on memory bus lines. This device consists of a 16-bit high-speed Schottky diode array suitable for clamping to VCC and/or GND. The SN74S1053 is characterized for ...
The \'283 and \'LS283 adders are electrically and functionally identical to the \'83A and \'LS83A, respectively; only the arrangement of the terminals has been changed. The \'S283 high performance versions are also functionally identical. These improved ...
The \'283 and \'LS283 adders are electrically and functionally identical to the \'83A and \'LS83A, respectively; only the arrangement of the terminals has been changed. The \'S283 high performance versions are also functionally identical. These improved ...
The SN54AS181B and SN74AS181A arithmetic Logic units (ALUs)/function generators have a complexity of 75 equivalent gates on a monolithic chip. These circuits perform 16 binary arithmetic operations on two 4-bit words as shown in Tables1 and 2. These operations ...
The \'LS181 and \'S181 are arithmetic Logic units (ALU)/function generators that have a complexity of 75 equivalent gates on a monolithic chip. These circuits perform 16 binary arithmetic operations on two 4-bit words as shown in Tables 1 and 2. These ...
The 74ACT11286 universal 9-bit parity generator/checker features a local output for parity checking and a bus-driving parity I/O port for parity generation/checking. The word-length capability is easily expanded by cascading. The control input is ...
The CD74AC280 and ?ACT280 are 9-bit odd/even parity generator/checkers that utilize Advanced CMOS Logic technology. Both even and odd parity outputs are available for checking or generating parity for words up to nine bits long. Even parity is indicated (E ...
The CD74ACT280 and ?ACT280 are 9-bit odd/even parity generator/checkers that utilize Advanced CMOS Logic technology. Both even and odd parity outputs are available for checking or generating parity for words up to nine bits long. Even parity is indicated (E ...
The CD74HC280 and ?HCT280 are 9-bit odd/even parity, generator checker devices. Both even and odd parity outputs are available for checking or generating parity for words up to nine bits long. Even parity is indicated (E output is high) when an even number ...
The CD74HCT280 and ?HCT280 are 9-bit odd/even parity, generator checker devices. Both even and odd parity outputs are available for checking or generating parity for words up to nine bits long. Even parity is indicated (E output is high) when an even number ...
These universal 9-bit parity generators/checkers SN74ALS280 utilize advanced Schottky high-performance circuitry and feature odd ( ODD) and even ( EVEN) outputs to facilitate operation of either odd- or even-parity applications. The word-length ...
These universal 9-bit parity generators/checkers SN74AS280 utilize advanced Schottky high-performance circuitry and feature odd ( ODD) and even ( EVEN) outputs to facilitate operation of either odd- or even-parity applications. The word-length ...
The SN54AS286 and SN74AS286 universal 9-bit parity generators/checkers SN74AS286 feature a local output for parity checking and a 48-mA bus-driving parity input/output (I/O) port for parity generation/checking. The word-length capability is easily expanded ...
These universal, monolithic, 9-bit parity generators/checkers SN74F280B feature odd and even outputs to facilitate operation of either odd or even parity application. The word-length capability is easily expanded by cascading. The SN54F280B is ...
These universal, monolithic, nine-bit parity generators/checkers SN74LS280 utilize Schottky-clamped TTL high-performance circuitry and feature odd/even outputs to facilitate operation of either odd or even parity application. The word-length capability is ...
These universal, monolithic, nine-bit parity generators/checkers SN74S280 utilize Schottky-clamped TTL high-performance circuitry and feature odd/even outputs to facilitate operation of either odd or even parity application. The word-length capability is ...
The 74F280B is a 9-bit Parity Generator or Checker commonly used
to detect errors in high speed data transmission or data retrieval
systems. Both Even (E) and Odd (O) parity outputs are available
for generating or checking even or odd parity on up to 9 ...
The 74F283 adds two 4-bit binary words (An plus Bn) plus the
incoming carry. The binary sum appears on the sum outputs
(0,3) and the outgoing carry (C OUT ) according to the equation:
CIN +20 (A0+B0)+21 (A1+B1)+22 (A2+B2)+23 ...
The 74F786 is an asynchronous 4,bit arbiter designed for high speed real,time applications. The priority of arbitration is determined on a first,come first,served basis. Separate bus grant (BGn) outputs are available to indicate which one of the request inputs ...
The 74HC283 is a high-speed Si-gate CMOS device and is pin compatible with low power
Schottky TTL (LSTTL). The 74HC283 is specified in compliance with JEDEC
standard no. 7A.
The 74HC283 adds two 4-bit binary words (An plus Bn) plus the incoming carry ...
The 74HC/HCT147 are high-speed Si-gate CMOS devices and are pin compatible with low power Schottky TTL (LSTTL). They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT147 9-input priority encoders accept data from nine active LOW inputs (A0 ...
The 74HC/HCT280 are high-speed Si-gate CMOS devices and are pin compatible with low power Schottky TTL (LSTTL). They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT280 are 9-bit parity generators or checkers commonly used to detect errors ...
The 74HC/HCT4016 are high-speed Si-gate CMOS devices and are pin compatible with the \'4016\' of the \'4000B\' series. They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT4016 have four independent analog switches (transmission gates). ...
The 74HC/HCT4316 are high-speed Si-gate CMOS devices. They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT4316 have four independent analog switches. Each switch has two input/output terminals (nY, nZ) and an active HIGH select input (nS). ...
The 74LVC1G66 is a low-power, low-voltage Si-gate CMOS device.
The 74LVC1G66 provides one single pole, single-throw analog switch function. It has two
input/output terminals (Yand Z) and an active HIGH enable input pin (E). When E is LOW,
the analog switch ...
The 74LVC2G66 is a low-power, low-voltage, high-speed Si-gate CMOS device.
The 74LVC2G66 provides two single pole, single-throw analog switch functions. Each
switch has two input/output terminals (nY and nZ) and an active HIGH enable input (nE).
When nE is ...
The 74LVCV2G66 is a high-performance, low-power, low-voltage, Si-gate CMOS device
that provides superior performance to most advanced CMOS compatible TTL families.
The 74LVCV2G66 provides two single pole, single throw analog or digital switches. Each
switch ...
The I-CODE1 label IC is a dedicated chip for intelligent
label applications for logistics and retail (including EAS)
and for baggage and parcel identification in airline
business and mail services.
The I-CODE system offers the possibility of ...
The I-CODE1 label IC is a dedicated chip for intelligent
label applications for logistics and retail (including EAS)
and for baggage and parcel identification in airline
business and mail services.
The I-CODE system offers the possibility of ...
The HEF4585B is a 4-bit magnitude comparator which compares two 4-bit words (A and B), whether they are ,less than,,, equal to,, or ,greater than,. Each word has four parallel inputs (A0 to A3 and B0 to B3 ); A3 and B3 being the most significant inputs. Three ...
The 74LVQ280 is a low voltage CMOS 9 BIT
PARITY GENERATOR fabricated with sub-micron
2
silicon gate and double-layer metal wiring C MOS
technology. It is ideal for low power and low noise
3.3V applications. ...
The HCF4066B is a monolithic integrated circuit
fabricated in Metal Oxide Semiconductor
technology available in DIP and SOP packages.
The HCF4066B is a QUAD BILATERAL SWITCH
intended for the transmission or multiplexing of
analog or digital signals. ...
The HCF4094B is a monolithic integrated circuit
fabricated in Metal Oxide Semiconductor
technology available in DIP and SOP packages.
The HCF4094B is an 8 stages serial shift register
having a storage latch associated with each stage
for strobing data ...
The SY55856U is a 2.5GHz, two-channel, fully differential
CML (Current Mode Logic) delay line. The device is
optimized to adjust the relative delay between two channels,
such as clock and data, in 50ps increments. Both inputs
may be adjusted in either ...
The SY58020U is a 2.5V/3.3V precision, high-speed, fully
differential 1:4 CML fanout buffer. Optimized to provide four
identical output copies with less than 15ps of skew and less
than 10ps total jitter, the SY58020U can process clock
PP
signals as fast ...
The SY58603U is a 2.5/3.3V, high-speed, fully
differential CML buffer optimized to provide less than
10pspp total jitter. The SY58603U can process clock
signals as fast as 2.5GHz or data patterns up to
4.25Gbps. ...
The TC74HC280A is a high speed CMOS 9-BIT PARITY
2
GENERATOR fabricated with silicon gate C MOS technology.
It achieves the high speed operation similar to equivalent
LSTTL while maintaining the CMOS low power dissipation. ...
The TC90A44P, TC90A45P / F separates luminance (Y) and
chrominance (C) signals from NTSC system composite video signal
by using 2 horizontal (H) lines separation. The Y / C separation unit
for TV and VCR set is able to assembled at low cost, because it ...
Look-Ahead Carry Generator HD74HC182 The HD74HC182 is a high-speed Carry Lockahead Generator. It is used with the HD74HC181 4-Bit
Arithmetic Logic Unit to provide high-speed lockahead over World lengths of more than four bits. The
device accepts up to four ...
M66014 semiconductor integrated circuit is a serial bus controller. It converts 2-byte parallel data that arrives from
microcomputer into serial and outputs it to serial bus. It also converts serial data input from serial bus into parallel and
outputs it ...
This improved full adder performs the addition of two 4-bit binary numbers. HD74HC83 The sum (, output are provided for each
bit and the resultant carry (C4) is obtained from the fourth bit.
This adder features full internal look ahead across all four ...
The KIC7S66FU is a high speed C MOS BILATERAL SWITCH
2
fabricated with silicon gate C MOS technology.
It consists of a high speed switch capable of controlling either digital
2
or analog signals while maintaining the C MOS low power dissipation
Control ...
2
The KIC7W66FK is a high speed C MOS DUAL BILATERAL
2
SWITCH fabricated with silicon gate C MOS technology.
It consists of four independent high speed switches capable of
controlling either digital or analog signals while maintaining the
CMOS low power ...
Pericom Semiconductors PI74LCX series of Logic circuits ar
produced in the Companys advanced 0.6 micron CMOS technology
achieving industry leading speed grades.
The PI74LCX16245 is a 16-bit bidirectional transceiver designed for
asynchronous two-way ...
The PI90LV024 and PI90LVB024 are monolithic dual 2x2
asynchronous crosspoint/repeater switches. The crosspoint func-
tion is based on a multiplexer tree architecture. Each 2x2 switch
can be considered as a pair of 2:1 multiplexers that share the ...
The 54HSC/T630 is a 16-bit parallel Error Detection and
Correction circuit. It uses a modified Hamming code to
generate a 6-bit check word from each 16-bit data word. The
check word is stored with the data word during a memory write
cycle. During a memory ...
The L4C381 is a flexible, high speed,
cascadable 16-bit Arithmetic and
Logic Unit. It combines four 381-type
4-bit ALUs, a look-ahead carry
generator, and miscellaneous interface
Logic all in a single 68-pin package.
While containing new features ...
The L4C383 is a flexible, high speed,
cascadable 16-bit Arithmetic and Logic
Unit. The L4C383 is capable of
performing up to 32 different
arithmetic or Logic functions.
The L4C383 can be cascaded to perform
32-bit or greater operations. See
Cascading ...
The L9700 is a monolithic circuit which is suited for
input protectionand voltage clamping purpose.
The limiting function is referred to ground and the
positive supply voltage.
One single element contains six independentchan-
nels.
Very fast speed is ...
CD4008BMS types consist of four full adder stages with fast
look ahead carry provision from stage to stage. Circuitry is
included to provide a fast parallel-carry-out but to permit
high-speed operation in arithmetic sections using ...
The Intersil HCTS283MS is a Radiation Hardened 4 bit
binary full adder with fast carry that adds two 4 bit binary
numbers and generates a carry-out bit if the sum exceeds 15.
This device can be used in positive or negative Logic When
using positive logic ...
These full adders perform the addition of two 4-bit binary
numbers 54LS283/DM54LS283/DM74LS283 . The sum (R) outputs are provided for each bit and
the resultant carry (C4) is obtained from the fourth bit.
These adders feature full internal look ahead across ...
The 74HC/HCT280 are high-speed Si-gate CMOS devices
and are pin compatible with low power Schottky TTL
(LSTTL). They are specified in compliance with JEDEC
standard no. 7A.
The 74HC/HCT280 are 9-bit parity generators or checkers
commonly used to detect ...
The 74HC2G66; 74HCT2G66 is a high-speed Si-gate
CMOS device.
The 74HC2G66; 74HCT2G66 provides a dual analog
switch. Each switch has two pins (nY and nZ) for input or
output and an active HIGH enable input (pin E). When
pin E is LOW, the belonging ...
The AC280 is an advanced high-speed CMOS 9
BIT PARITY GENERATOR - CHECKER
fabricated with sub-micron silicon gate and
double-layermetal wiring C2
MOS technology. It is
ideal for low power applications mantaining high
speed operation similar to eqivalent ...
