The EL6201 is a solid state high performance laser modulation oscillator with external resistor adjustable frequency and amplitude. The EL6201 is available in both the 8 Ld MSOP and the 5 Ld SOT-23, to enable device placement close to the laser for reduced ...
The EL6203 is a push-pull oscillator used to reduce laser noise. It uses the standard interface to existing ROM controllers. The frequency and amplitude are each set with a separate resistor connected to ground. The tiny package and harmonic reduction allow ...
The EL6204 is a push-pull oscillator used to reduce laser noise. It uses the standard interface to existing ROM controllers. The frequency and amplitude are each set with a separate resistor connected to ground. The tiny package and harmonic reduction allow ...
The EL6208 is a dual push-pull oscillator used to reduce laser noise in twin laser diodes. It uses the standard interface to existing ROM controllers. The frequency and amplitude are both set with a separate resistor connected to ground. The tiny package and ...
The Intersil HSP45102 is Numerically Controlled Oscillator (NCO12) with 32-bit frequency resolution and 12-bit output. With over 69dB of spurious free dynamic range and worst case frequency resolution of 0.009Hz, the NCO12 provides significant accuracy for ...
The Intersil HSP45116A combines a high performance quadrature numerically controlled oscillator (NCO) and a high speed 16-bit Complex Multiplier/Accumulator (CMAC) on a single IC. This combination of functions allows a complex vector to be multiplied by ...
The LTC6902 is a precision, low power and easy-to-use oscillator that provides multiphase outputs in a small package. The oscillator frequency is set by a single external resistor (RSET). The LTC6902 also provides an optional spread spectrum frequency ...
The LTC6903/LTC6904 are low power self contained digital frequency sources providing a precision frequency from 1kHz to 68MHz, set through a serial port. The LTC6903/LTC6904 require no external components other than a power supply bypass capacitor, and they ...
The LTC6903/LTC6904 are low power self contained digital frequency sources providing a precision frequency from 1kHz to 68MHz, set through a serial port. The LTC6903/LTC6904 require no external components other than a power supply bypass capacitor, and they ...
The LTC6905 precision, programmable silicon oscillator is easy to use and occupies very little board space. It requires only a single resistor to set the output frequency from 17MHz to 170MHz with a typical frequency error of 0.5% or less. The LTC6905 ...
The LTC6905-XXX series of parts are precision, fixed frequency, silicon Oscillators designed to minimize board space while maximizing accuracy and ease of use.
Programmed at the factory to a fixed frequency, the LTC6905-XXX series of parts need no external ...
The LTC6905-XXX series of parts are precision, fixed frequency, silicon Oscillators designed to minimize board space while maximizing accuracy and ease of use.
Programmed at the factory to
506
a fixed frequency, the LTC6905-XXX series of parts need no ...
The LTC6905-XXX series of parts are precision, fixed frequency, silicon Oscillators designed to minimize board space while maximizing accuracy and ease of use.
Programmed at the factory to a fixed frequency, the LTC6905-XXX series of parts need no external ...
The LTC6905-XXX series of parts are precision, fixed frequency, silicon Oscillators designed to minimize board space while maximizing accuracy and ease of use.
Programmed at the factory to a fixed frequency, the LTC6905-XXX series of parts need no external ...
The LTC6906 is a precision programmable oscillator that is versatile, compact and easy-to-use. Micropower operation benefits portable and battery-powered equipment. At 100kHz, the LTC6906 consumes 12A on a 3.3V supply.
A single resistor programs the ...
The LTC6907 is a precision programmable oscillator that is versatile, compact and easy to use. Micropower operation benefits portable and battery-powered equipment. At 400kHz, the LTC6907 consumes 36A on a 3V supply.
A single resistor programs the oscillator ...
The LTC6908 is an easy-to-use precision oscillator that provides 2-outputs, shifted by either 180 or 90
83b
. The oscillator frequency is programmed by a single external resistor (RSET) and spread spectrum frequency modulation (SSFM) can be activated for ...
The MAX7381 is a silicon oscillator intended as a low-cost
improvement to ceramic resonators, crystals, and crystal
oscillator modules as the clock source for microcontrollers
and UARTs in 3V, 3.3V, and 5V applications.
The MAX7381 is an integrated ...
The MAX7384 dual-speed silicon oscillator replaces
ceramic resonators, crystals, and crystal-oscillator
modules as the primary and secondary clock source for
microcontrollers in 3V, 3.3V, and 5V applications. The
MAX7384 features a factory-programmed ...
The DS1094L is a silicon oscillator that generates four multiphase, spread-spectrum, square-wave outputs. Frequencies between 2MHz and 31.25kHz can be output in either two, three, or four-phase mode. The internal master oscillator can be dithered by either 0, ...
The DS1099 is a low-cost, low-power, low-frequency silicon oscillator that generates two square-wave outputs with frequencies between 0.25Hz and 1.048MHz. Individual output enables allow both outputs to be enabled/disabled independently. Both outputs are ...
The DS1090 is a low-cost, dithered oscillator intended
to be used as an external clock for switched-mode
power supplies and other low-frequency applications.
The dithering or sweeping function reduces peak-radiated
emissions from the power supply at its ...
The DS1089L is a clock generator that produces a spread spectrum (dithered) square-wave output of frequencies from 130kHz to 66.6MHz. The DS1089L is shipped from the factory programmed at a specific frequency. The DS1089L is pin-for-pin compatible with the ...
The DS1088L is a low-cost clock generator that produces
a square-wave output without external timing
components. The fixed-frequency oscillator is available
in factory-calibrated frequencies from 312kHz to
133MHz. The DS1088L has a power-down pin ...
The MAX7377 dual-speed silicon oscillator with reset is
a replacement for ceramic resonators, crystals, crystal
oscillator modules, and discrete reset circuits. The
device provides the primary and secondary clock
source for microcontrollers in 3V, 3.3V, ...
The MAX7383 dual-speed silicon oscillator replaces
ceramic resonators, crystals, and crystal-oscillator
modules as the primary and secondary clock source for
microcontrollers in 3V, 3.3V, and 5V applications. The
MAX7383 features a factory-programmed ...
The DS32kHz is a temperature-compensated
crystal oscillator (TCXO) with an output
frequency of 32.768kHz. This device addresses
applications requiring better timekeeping
accuracy, and can be used to drive the X1 input
of most Dallas Semiconductor ...
The DS1077L is a dual-output, programmable, fixed-frequency oscillator requiring no external
components for operation. The DS1077L can be used as a processor-controlled frequency synthesizer or
as a stand-alone oscillator. The two synchronous output ...
The MAX2620 combines a low-noise oscillator with two output buffers in a low-cost, plastic surface-mount, ultra-small MAX package. This device integrates functions typically achieved with discrete components. The oscillator exhibits low-phase noise when ...
XO-53 - Full Size Clock Oscillators TTL Compatible - Vishay Oscillators XO-53 The XO-53 series oscillator is TTL compatible and features
fast rise/fall times with high reliability at low cost. The metal
package with pin#7 case ground acts as shielding to ...
XO-54 - Full Size Clock Oscillators TTL/HCMOS Compatible - Vishay Oscillators XO-54 The XO-54 series oscillator is Full Size Tri-state
Enable/Disable control. The metal package with pin #7 case
ground acts as shielding to minimize EMI radiation. ...
XO-543 - Full Size Clock Oscillators TTL/HCMOS Compatible - Vishay Oscillators XO-543 The XO-543 series is with 3.3 V power supply. The metal
package with pin #7 case ground acts as shielding to
minimize EMI radiation. ...
XOSM-52 - Half Size Clock Oscillator Enable/Disable - Vishay Oscillators XOSM-52 The XOSM-52 series oscillator is half size, has Tri-state
enable/disable controlled function. The metal package with
pin#4 case ground acts as shielding to minimize EMI ...
XO-52 - Half Size Clock Oscillators Enable/Disable - Vishay Oscillators XO-52 The XO-52 series oscillator is half size, has Tri-state
enable/disable controlled function. The metal package with
pin#4 case ground acts as shielding to minimize EMI radiation. ...
XO-523 - Half Size Clock Oscillators Enable/Disable - Vishay Oscillators XO-523 The XO-523 series oscillator is half size, has Tri-state
enable/disable controlled function, and is with a 3.3 V power
supply voltage. The metal package with pin#4 case ...
XOSM-572 - Suirface Mount Oscillator - Vishay Oscillators XOSM-572 The XOSM-572 series is an ultra miniature package clock
oscillator with dimensions 7.0 x 5.0 x 1.5 mm. It is mainly
used in portable PC and telecommunication devices and
equipment. ...
XOSM-532 - Surface Mount Oscillator - Vishay Oscillators XOSM-532 The XOSM-532 series is an ultra miniature package clock
oscillator with dimensions 5.0 x 3.2 x 1.3 mm. It is mainly used
in portable PC and telecommunication devices and equipment. ...
XOSM-533 - Surface Mount Oscillator - Vishay Oscillators XOSM-533 The XOSM-533 series is an ultra miniature package clock
oscillator with dimensions 5.0 x 3.2 x 1.3 mm. It is mainly
used in portable PC and telecommunication devices and
equipment. ...
XOSM-57 - Surface Mount Oscillator - Vishay Oscillators XOSM-57 The XOSM-57 series is an ultra miniature package clock
oscillator with dimensions 7.0 x 5.0 x 1.6 mm. It is mainly
used in portable PC and telecommunication devices and
equipment. ...
XOSM-571 - Surface Mount Oscillator - Vishay Oscillators XOSM-571 The XOSM-571 series is an ultra miniature package clock
oscillator with dimensions 7.0 x 5.0 x 1.5 mm. It is mainly
used in portable PC and telecommunication devices and
equipment. ...
XOSM-573 - Surface Mount Oscillator - Vishay Oscillators XOSM-573 The XOSM-573 series is an ultra miniature package clock
oscillator with dimensions 7.0 x 5.0 x 1.6 mm. It is mainly
used in portable PC and telecommunication devices and
equipment. ...
XOSM-531 - Surface Mount Oscillators - Vishay Oscillators XOSM-531 The XOSM-531 series is an ultra miniature package clock
oscillator with dimensions 5.0 x 3.2 x 1.3 mm. It is mainly used
in portable PC and telecommunication devices and equipment. ...
The HMC535LP4(HMC535LP4E) is a GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC PLO. The PLOs phase noise performance is excellent over temperature, shock, and process due to the Oscillators monolithic structure. Power output is +9 dBm typical from a ...
In house programming of samples and prototype quantities is
available using CY3672 programming kit and CY3724 socket
adapters. Production quantities are available through Cypress
value added distribution partners or by using third party
programmers from ...
CY2037 is an EPROM-programmable, high accuracy,
PLL-based die designed for the crystal oscillator market. The die
attaches directly to a low cost 10 - 30 MHz crystal and can be
packaged into a 4-pin through-hole or surface mount packages.
The oscillator ...
The CY25701JXC/FJXC is a Spread Spectrum Crystal Oscil-
lator (SSXO) IC used for the purpose of reducing EMI found in
todays high-speed digtal electronic systems. ...
Features
, Bias resistors, a transistor for oscillation and a transistor for
buffer are packed in one package; hence, TA4014FE can easily
compose a crystal oscillator.
, TA4014FE comes with a 6-pin thin ultra-compact package ...
Features
, Bias resistors, a transistor for oscillation and a transistor for
buffer are packed in one package; hence, TA4015FT can easily
compose a crystal oscillator. ...
The MK3200 is IDT\'s lowest cost, low power clock oscillator that generates a low power 32.768 kHz output from an inexpensive 32.768 kHz crystal. This part includes a power down pin and allows you to tri state the output clock for in-circuit testing.
IDT ...
The XC2141 series are a group of high frequency, CMOS low power crystal Oscillators with on-chip divider circuitry that operate from a supply voltage of 3.5V. ...
The XC2163 series are high frequency, low current consumption CMOS ICs with built-in crystal oscillator and divider circuits. Output is selectable from any one of the following values for f0 : f0/1, f0/2, f0/4, f0/8. With oscillation capacitors and a ...
The XC2164 series are high frequency, low current consumption CMOS ICs with built-in crystal oscillator and divider circuits.
For fundamental oscillation, output is selectable from any one of the following values for f0 : f0/1, f0/2, f0/4, f0/8.
With ...
The NJU6311 is a fundamental quartz crystal oscillator, up to 50MHz. The oscillation amplifier incorporates feedback resistor and capacitors (Cg, Cd), therefore, it requires no external component expect quartz crystal, and realizes very low standby current ...
The NJU6318 series is a C-MOS quartz crystal oscillator which consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. The oscillation frequency is as wide as up to 50MHz and the symmetry of 45-55% is realized over full oscillation ...
The NJU6319 series is a C-MOS quartz crystal oscillator which contains of an oscillation amplifier, 3-stage divider and 3-state output buffer. The oscillation frequency is as wide as up to 50MHz and the symmetry of 45-55% is realized over full oscillation ...
The NJU6321 series is a C-MOS quartz crystal oscillator which consists of an oscillation amplifier, 3-stage divider, output frequency selector and 3-state output buffer. The oscillation frequency is as wide as up to 50MHz and the symmetry of 45-55% is realized ...
The NJU6322 series is a C-MOS quartz crystal oscillator which consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. The oscillation frequency is as wide as up to 50MHz and the symmetry of 45-55% is realized over full oscillation ...
The NJU6330 series is a C-MOS quartz crystal oscillator which contsists of an oscillation amplifier, and 3-state output buffer. This series are classed into three versions. A, B and C according to their oscillation frequency range mentioned in the line-up ...
The NJU6333 series is a C-MOS quartz crystal oscillator which contsists of an oscillation amplifier and a 3-state output buffer. This series are classed into three versions. A, H and Q according to their oscillation frequency range mentioned in the line-up ...
The NJU6338 series is a C-MOS quartz crystal oscillator which contsists of an oscillation amplifier, 3-state divider and 3-stage output buffer. This series are classed into three groups A to D, H to L and Q to T according to their oscillation frequency range ...
The NJU6339 series is a C-MOS quartz crystal oscillator which contsists of an oscillation amplifier, 3-state divider and 3-stage output buffer. This series are classed into three groups A to D, H to L and Q to T according to their oscillation frequency range ...
The NJU6323 series is a C-MOS quartz crystal oscillator which contains of an oscillation amplifier, 3-stage divider, output frequency selector and 3-state output buffer. The oscillation frequency is as wide as up to 50MHz and the symmetry of 45-55% is realized ...
The NJU6324 series is a C-MOS quartz crystal oscillator which contsists of an oscillation amplifier, 3-stage divider, and 3-state output buffer. The oscillation frequency is as wide as up to 50MHz and the symmetry of 45-55% is realized over full oscillation ...
The NJU6360 series is a C-MOS fundamental quartz crystal oscillator that consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. The 5-stage divider generates only one frequency selected of f0,f0/2,f0/4 f0/8, f0/16 and f0/32 by ...
The NJU6363 series is a C-MOS fundamental quartz crystal oscillator that consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. The 3-stage divider generates only one frequency selected of f0,f0/2,f0/4 f0/8, f0/16 and f0/32 by ...
The NJU6366 series is a C-MOS fundamental quartz crystal oscillator that consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. The 3-stage divider generates only one frequency selected of f0,f0/2,f0/4 and f0/8 by internal circuits is ...
The NJU6367 series is a C-MOS fundamental quartz crystal oscillator that consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. The 3-stage divider generates only one frequency selected of f0,f0/2,f0/4 f0/8, f0/16 and f0/32 by ...
The NJU6368 series is a C-MOS fundamental quartz crystal oscillator that consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. The 3-stage divider generates only one frequency selected of f0,f0/2,f0/4 and f0/8 by internal circuits is ...
The NJU6369 series is a C-MOS IC for fundamental quartz crystal oscillator that consists of an oscillation amplifier, 5-stage divider and 3-state output buffer, and can oscillate at 1.5V very low voltage. The 5-stage divider generates only one frequency ...
The NJU6370 series is a C-MOS 3rd. over tone quartz crystal oscillator that consists of an oscillation amplifier and 3-state output buffer. The NJU6378 series has 4-types according to their frequency ranges as shown in the line-up table. The oscillation ...
The NJU6373 series is a C-MOS quartz crystal oscillatior which consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. This series are classed into three groups A to D, H to L and Q to T according to their oscillation frequency range ...
The NJU6374 series is a C-MOS quartz crystal oscillatior which consists of an oscillation amplifier, 3-stage divider and 3-state output buffer. This series are classed into three groups A to D, H to L and Q to T according to their oscillation frequency range ...
The NJU6375 series is a C-MOS quartz crystal oscillatior which consists of an oscillation amplifier and a 3-state output buffer. This series are classed into six viesions A, B, C and H, J, K according to their oscillation frequency range mentioned in the ...
The NJU6376 series is a C-MOS 3rd. over tone quartz crystal oscillator that consists of an oscillation amplifier and 3-state output buffer. The type numbers are classed into four versions G, H, J and K according to their oscillation frequency range shown in ...
The NJU6377 series is a C-MOS 3rd. over tone quartz crystal oscillator that consists of an oscillation amplifier and 3-state output buffer. The type numbers are classed into three versions E, F, G and H according to their oscillation frequency range mentioned ...
The NJU6378 series is a C-MOS 3rd. over tone quartz crystal oscillator that consists of an oscillation amplifier and 3-state output buffer. The NJU6378 series has 4-types according to their frequency ranges as shown in the line-up table. The oscillation ...
The NJU6379D is a C-MOS IC for 3rd. overtone quartz crystal oscillator that consists of an oscillation amplifier and 3-state output buffer, and can oscillate at 1.8V very low voltage. The NJU6379D has ability to oscillate from 60 to 70 MHz. The oscillation ...
The NJU6391 series is a 3V operation C-MOS quartz crystal oscillator which contsists of an oscillation amplifier and 3-state output buffer. This series are classed into three versions. A, B and C according to their oscillation frequency range mentioned in the ...
The NJU6392 Series is a 3V operation C-MOS quartz crystal oscillator which consists of an oscillation amplifier and a 3-state output buffer. This siries is classed into four versions A, B, C and P according to their oscillation frequency range mentioned in the ...
The NJU6393 is a low voltage operation C-MOS quartz crystal oscillator which is possible to 65MHz, It consists of an oscillation amplifier and a 3-state output buffer. This oscillation amplifier incorporates feed-back resistance and oscillation capacitors (Cg, ...
The NJU6395 series is up to 125MHz low-voltage C-MOS quartz crystal oscillator, the NJU6395A is up to 110MHz and the NJU6395B is up to 125MHz. The NJU6395 series consists of an oscillation amplifier, internal capacitors (Cg, Cd), feedback resistance (Rf), and ...
The NJU6396 is a C-MOS IC for XOs, and can oscillate up to 166MHz maximum at very low operating voltage. High Fan-out is gained from low operating voltage with 3-state output buffer and the oscillation amplifier that is realized very low stand-by current using ...
The NJU6397 series that is a C-MOS IC for quartz crystal oscillator consists of an oscillation amplifier and 3-state output buffer. This series has three types of A, B and C. The frequency range of the A type is from 75 to 90MHz, and the B type is from 90 to ...
The NJU6364 series is a C-MOS IC for fundamental quartz crystal oscillator that consists of an oscillation amplifier,5-stage divider and 3-state output buffer.The operating voltage is from 2.0V to 3.6V and high frequency-stability based on most suitable ...
The NJU6365 series is a C-MOS IC for fundamental quartz crystal oscillator that consists of an oscillation amplifier,5-stage divider and 3-state output buffer.The operating voltage is from 1.8V to 3.6V and high frequency-stability based on most suitable ...
The WF5028 series are miniature crystal oscillator module ICs. The devices are fabricated using a proprietary
low voltage process, enabling 0.8V operation. The pad layouts are selective from 3 types depending on pack-
age structures, mounting methods, which ...
The CF5011 series are low-voltage crystal oscillator module ICs that operate at 1.8V. The crystal oscillator cir-
cuit and output buffer employ a low-voltage CMOS process operating at 1.8V. The crystal oscillator circuit has
a built-in thin-lm feedback ...
The CF5016 series are 1.8V operation crystal oscillator ICs. They are available for frequencies up to 50MHz.
They employ a recently developed low-voltage process optimized for operation at 1.8V, resulting in stable
operation at low voltages while maintaining ...
The CF5015 series are 2.5V operation crystal oscillator ICs. They are available for frequencies up to 60MHz.
The product lineup consists of AL series for 2.5V exclusive use and BL series compliant with 2.5V to 5V.
The built-in oscillator capacitor of AL ...