24-Bit FET Switch With Precharged Outputs 2.5-V/3.3-V Low-Voltage High-Bandwidth Bus Switch

The SN74CB3Q16811 is a high-bandwidth FET bus Switch utilizing a Charge Pump to elevate the Gate voltage of the pass Transistor providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports Rail-to-Rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q16811 provides an optimized Interface solution ideally suited for Broadband Communications networking, and data-intensive computing systems. The SN74CB3Q16811 is organized as two 12-bit Bus Switches with separate output-enable (1OE, 2OE) inputs. It CAN be used as two 12-bit Bus Switches or as one 24-bit bus Switch When OE is low, the associated 12-bit bus Switch is ON, and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the associated 12-bit bus Switch is OFF, and a high-impedance state exists between the A and B ports. The B port is precharged to BIASV through the equivalent of a 10-k resistor when OE is high, or if the device is powered down (VCC = 0 V). During insertion (or removal) of a card into (or from) an active bus, the card?s output voltage may be close to GND. When the connector pins make contact, the card?s parasitic capacitance tries to force the bus signal to GND, creating a possible glitch on the active bus. This glitching effect CAN be reduced by using a bus Switch with precharged bias voltage (BIASV) of the bus Switch equal t 145a o the input threshold voltage level of the receivers on the active bus. This method will ensure that any glitch produced by insertion (or removal) of the card will not cross the input threshold region of the receivers on the active bus, minimizing the effects of live-insertion noise. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry prevents damaging current backflow through the device when it is powered down. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
By Texas Instruments
Part Manufacturer Description Datasheet Samples
SN74CB3Q16811DLG4 Texas Instruments 24-Bit FET Switch with Precharged Outputs 2.5-V/3.3-V Low-Voltage High-Bandwidth Bus Switch 56-SSOP -40 to 85
SN74CB3Q16811DL Texas Instruments 24-Bit FET Switch with Precharged Outputs 2.5-V/3.3-V Low-Voltage High-Bandwidth Bus Switch 56-SSOP -40 to 85
SN74CB3Q16811DLR Texas Instruments 24-Bit FET Switch with Precharged Outputs 2.5-V/3.3-V Low-Voltage High-Bandwidth Bus Switch 56-SSOP -40 to 85
SN74CB3Q16811DGVR Texas Instruments 24-Bit FET Switch with Precharged Outputs 2.5-V/3.3-V Low-Voltage High-Bandwidth Bus Switch 56-TVSOP -40 to 85
SN74CB3Q16811DGGR Texas Instruments 24-Bit FET Switch with Precharged Outputs 2.5-V/3.3-V Low-Voltage High-Bandwidth Bus Switch 56-TSSOP -40 to 85
SN74CB3Q16811 's PackagesSN74CB3Q16811 's pdf datasheet
74CB3Q16811DGGRE4 TSSOP
74CB3Q16811DGGRG4 TSSOP
74CB3Q16811DGVRE4 TVSOP
74CB3Q16811DGVRG4 TVSOP
74CB3Q16811DLRG4 SSOP
SN74CB3Q16811DGGR TSSOP
SN74CB3Q16811DGVR TVSOP
SN74CB3Q16811DL SSOP
SN74CB3Q16811DLG4 SSOP
SN74CB3Q16811DLR SSOP

SN74CB3Q16811 pdf datasheet download


SN74CB3Q16811 Pinout, Pinouts
SN74CB3Q16811 pinout,Pin out
This is one package pinout of SN74CB3Q16811,If you need more pinouts please download SN74CB3Q16811's pdf datasheet.

SN74CB3Q16811 circuits will be updated soon..., now you can download the pdf datasheet to check the circuits!

Related Electronics Part Number

Related Keywords:

SN74CB3Q16811 Pb-Free SN74CB3Q16811 Cross Reference SN74CB3Q16811 Schematic SN74CB3Q16811 Distributor
SN74CB3Q16811 Application Notes SN74CB3Q16811 RoHS SN74CB3Q16811 Circuits SN74CB3Q16811 footprint
Hot categories