SSTUB32864 1.8 V Configurable Registered Buffer For DDR2-800 RDIMM Applications

The SSTUB32864 is a 25-bit 1 : 1 or 14-bit 1 : 2 configurable registered Buffer designed for 1.7 V to 2.0 V VDD operation. All Clock and data inputs are compatible with the JEDEC standard for SSTL_18. The control inputs are LVCMOS. All outputs are 1.8 V CMOS drivers that have been optimized to drive the DDR2 DIMM load. The SSTUB32864 operates from a differential Clock (CK and CK). Data are registered at the crossing of CK going HIGH, and CK going LOW. The C0 input controls the pinout configuration of the 1 : 2 pinout from A configuration (when LOW) to B configuration (when HIGH). The C1 input controls the pinout configuration from 25-bit 1 : 1 (when LOW) to 14-bit 1 : 2 (when HIGH). The device supports low-power standby operation. When the reset input (RESET) is LOW, the differential input receivers are disabled, and un-driven (floating) data, Clock and reference voltage (VREF) inputs are allowed. In addition, when RESET is LOW all Registers are reset, and all outputs are forced LOW. The LVCMOS RESET and Cn inputs must always be held at a valid Logic HIGH or LOW level. To ensure defined outputs from the Register before a stable Clock has been supplied, RESET must be held in the LOW state during power-up. In the DDR2 RDIMM application, RESET is specified to be completely asynchronous with respect to CK and CK. Therefore, no Timing relationship CAN be guaranteed between the two. When entering reset, the Register will be cleared and the data outputs will be driven LOW quickly, relative to the time to disable the differential input receivers. However, when coming out of reset, the Register will become active quickly, relative to the time to enable the differential input receivers. As long as the data inputs are LOW, and the Clock is stable during the time from the LOW-to-HIGH transition of RESET until the input receivers are fully enabled, the design of the SSTUB32864 must ensure that the outputs will remain LOW, thus ensuring no glitches on the output. The device monitors both DCS and CSR inputs and will Gate the Qn outputs from changing states when both DCS and CSR inputs are HIGH. If either DCS or CSR input is LOW, the Qn outputs will function normally. The RESET input has priority over the DCS and CSR control and will force the outputs LOW. If the DCS-control functionality is not desired, then the CSR input CAN be hardwired to ground, in which case the set-up time requirement for DCS would be the same as for the other Dn data inputs. The SSTUB32864 is available in a 96-ball, low profile fine-pitch ball grid array (LFBGA96) package.
By NXP Semiconductors
Part Manufacturer Description Datasheet Samples
74SSTUB32864AZKER Texas Instruments 25-Bit Configurable Registered Buffer with SSTL_18 Inputs and Outputs 96-LFBGA 0 to 70
SN74SSTUB32864ZKER Texas Instruments 25-Bit Configurable Registered Buffer with SSTL_18 Inputs and Outputs 96-LFBGA -40 to 85
SSTUB32864 's PackagesSSTUB32864 's pdf datasheet
SSTUB32864EC-G LFBGA




SSTUB32864 Pinout will be updated soon..., now you can download the pdf datasheet to check the pinouts !
SSTUB32864 circuits will be updated soon..., now you can download the pdf datasheet to check the circuits!

Related Electronics Part Number

Related Keywords:

SSTUB32864 Pb-Free SSTUB32864 Cross Reference SSTUB32864 Schematic SSTUB32864 Distributor
SSTUB32864 Application Notes SSTUB32864 RoHS SSTUB32864 Circuits SSTUB32864 footprint