This device is designed to multiplex signals from 4-bit data sources to four output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable (OE) input is at a high logic level. To ensure the ...
The 74ACT11257 is designed to multiplex signals from 4-bit data sources to four output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable input is at a high logic level. The 74ACT11257 is ...
This data selector/multiplexer CD74AC151 provides full binary decoding to select one of eight data sources. The strobe (G) input must be at a low logic level to enable the inputs. A high level at the strobe terminal forces the W output high and the Y output ...
Each of these data selectors/multiplexers CD74AC153 contains inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate strobe (G) inputs are provided for each of the two 4-line sections. ...
These quadruple 2-line to 1-line data selectors/multiplexers CD74AC157 are designed for 1.5-V to 5.5-V VCC operation. The ?AC157 devices feature a common strobe (G) input. When the strobe is high, all outputs are low. When the strobe is low, a 4-bit word ...
This quadruple 2-line to 1-line data selector/multiplexer CD74AC158 is designed for 1.5-V to 5.5-V VCC operation. The CD74AC158 features a common strobe (G) input. When the strobe is high, all outputs are high. When the strobe is low, a 4-bit word is ...
The CD74AC251 and CD74ACT251 8-input multiplexers that utilize the Harris Advanced CMOS Logic technology. This multiplexer features both true (Y) and complement (Y) outputs as well as an Output Enable (OE) input. The OE must be at a LOW logic level to enable ...
The CD74AC253 and ?ACT253 dual 4-input multiplexers that utilize Advanced CMOS Logic technology. One of the four sources for each section is selected by the common Select inputs, S0 and S1. When the Output Enable (1OE or 2OE) is HIGH, the output is in the ...
The ?AC257, ?ACT257 and CD74ACT258 are quad 2-input multiplexers with three-state outputs that utilize Advanced CMOS Logic technology. Each of these devices selects four bits of data from two sources under the control of a common Select input (S). The Output ...
These data selectors/multiplexers CD74ACT151 provide full binary decoding to select one of eight data sources. The strobe (G) input must be at a low logic level to enable the inputs. A high level at the strobe terminal forces the W output high and the Y ...
Each of these data selectors/multiplexers CD74ACT153 contains inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate strobe (G) inputs are provided for each of the two 4-line sections. ...
This quadruple 2-line to 1-line data selector/multiplexer CD74ACT157 is designed for 4.5-V to 5.5-V VCC operation. The CD74ACT157 features a common strobe (G) input. When the strobe is high, all outputs are low. When the strobe is low, a 4-bit word is ...
This quadruple 2-line to 1-line data selector/multiplexer CD74ACT158 is designed for 4.5-V to 5.5-V VCC operation. The CD74ACT158 features a common strobe (G) input. When the strobe is high, all outputs are high. When the strobe is low, a 4-bit word is ...
The CD74AC253 and ?ACT253 dual 4-input multiplexers CD74ACT253 that utilize Advanced CMOS Logic technology. One of the four sources
583
for each section is selected by the common Select inputs, S0 and S1. When the Output Enable (1OE or 2OE) is HIGH, the ...
The ?AC257, ?ACT257 and CD74ACT258 are quad 2-input multiplexers with three-state outputs that utilize Advanced CMOS Logic technology. Each of these devices selects four bits of data from two sources under the control of a common Select input (S). The Output ...
The ?AC257, ?ACT257 and CD74ACT258 are quad 2-input multiplexers with three-state outputs that utilize Advanced CMOS Logic technology. Each of these devices selects four bits of data from two sources under the control of a common Select input (S). The Output ...
The ?HC151 and ?HCT151 are single 8-channel digital multiplexers having three binary control inputs, S0, S1 and S2 and an active low enable (E) input. The three binary signals select 1 of 8 channels. Outputs are both inverting (Y) and non-inverting (Y). ...
The CD74HC153 and ?HCT153 are dual 4- to 1-line selector/multiplexers that select one of four sources for each section by the common select inputs, S0 and S1. When the enable inputs (1E, 2E) are HIGH, the outputs are in the LOW state. ...
The CD74HC157 , ?HCT157, ?HC158, and ?HCT158 are quad 2-input multiplexers which select four bits of data from two sources under the control of a common Select input (S). The Enable input (E) is active Low. When (E) is High, all of the outputs in the 158, the ...
The CD74HC251 and ?HCT251 are 8-channel digital multiplexers with three-state outputs, fabricated with high-speed silicon-gate CMOS technology. Together with the low power consumption of standard CMOS integrated circuits, they possess the ability to drive 10 ...
The CD74HC253 and CD74HCT253 are dual 4-to-1 line selector/multiplexers having three-state outputs. One of four sources for each section is selected by the common select inputs, S0 and S1. When the output enable (1OE, 2OE) is HIGH, the output is in the ...
The CD74HC257 and ?HCT257 are quad 2-input multiplexers which select four bits of data from two sources under the control of a common Select Input (S). The Output Enable input (OE) is active LOW. When OE is HIGH, all of the outputs (1Y-4Y) are in the high ...
The CD54HC354, CD74HC354, and CD74HCT354 are data selectors/multiplexers that select one of eight sources. In both types, the data select bits S0, S1 and S2 are stored in transparent latches that are enabled by a low latch enable input, LE. In the ...
The CD74HCT151 and ?HCT151 are single 8-channel digital multiplexers having three binary control inputs, S0, S1 and S2 and an active low enable (E) input. The three binary signals select 1 of 8 channels. Outputs are both inverting (Y) and non-inverting ...
The CD74HCT153 and ?HCT153 are dual 4- to 1-line selector/multiplexers that select one of four sources for each section by the common select inputs, S0 and S1. When the enable inputs (1E, 2E) are HIGH, the outputs are in the LOW state. ...
The CD74HCT157 , ?HCT157, ?HC158, and ?HCT158 are quad 2-input multiplexers which select four bits of data from two sources under the control of a common Select input (S). The Enable input (E) is active Low. When (E) is High, all of the outputs in the 158, ...
The CD74HCT158 , ?HCT157, ?HC158, and ?HCT158 are quad 2-input multiplexers which select four bits of data from two sources under the control of a common Select input (S). The Enable input (E) is active Low. When (E) is High, all of the outputs in the 158, ...
The CD74HCT251 and ?HCT251 are 8-channel digital multiplexers with three-state outputs, fabricated with high-speed silicon-gate CMOS technology. Together with the low power consumption of standard CMOS integrated circuits, they possess the ability to drive 10 ...
The CD74HC253 and CD74HCT253 are dual 4-to-1 line selector/multiplexers having three-state outputs. One of four sources for each section is selected by the common select inputs, S0 and S1. When the output enable (1OE, 2OE) is HIGH, the output is in the ...
The CD74HCT257 and ?HCT257 are quad 2-input multiplexers which select four bits of data from two sources under the control of a common Select Input (S). The Output Enable input (OE) is active LOW. When OE is HIGH, all of the outputs (1Y-4Y) are in the high ...
These devices are designed to multiplex CD74HCT258 signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable (G) input is at a high logic level. To ensure the ...
The CD54HC354, CD74HC354, and CD74HCT354 are data selectors/multiplexers that select one of eight sources. In both types, the data select bits S0, S1 and S2 are stored in transparent latches that are enabled by a low latch enable input, LE. In the ...
The CD74HCT356 consists of data selectors/multiplexers that select one of eight sources. The data select bits (S0, S1, and S2) are stored in transparent latches that are enabled by a low latch enable input (LE). The data is stored in edge-triggered ...
The CY74FCT257T has four identical two-input multiplexers that select four bits of data from two sources under the control of a common data-select (S) input. The I0 inputs are selected when S is low, and the I1 inputs are selected when S is high. Data at the ...
These monolithic data selectors/multiplexers contain full on-chip binary decoding to select the desired data source. The \'150 selects one-of-sixteen data sources; the \'151A, \'LS151, and \'S151 select one-of-eight data sources. The \'150, \'151A, \'LS151, ...
The \'ABTH16460 are 4-bit to 1-bit multiplexed registered transceivers used in applications where four separate data paths must be multiplexed onto or demultiplexed from a single data path. Typical applications include multiplexing and/or demultiplexing of ...
These quadruple 2-line to 1-line data selectors/multiplexers are designed for 2-V to 5.5-V VCC operation. The ?AHC157 devices feature a common strobe (G) input. When the strobe is high, all outputs are low. When the strobe is low, a 4-bit word is selected ...
These quadruple 2-line to 1-line data selectors/multiplexers are designed for 2-V to 5.5-V VCC operation. The SN74AHC158 devices feature a common strobe (G) input. When the strobe is high, all outputs are high. When the strobe is low, a 4-bit word is ...
These quadruple 2-line to 1-line data selectors/multiplexers are designed for 4.5-V to 5.5-V VCC operation. The SN74AHCT157 devices feature a common strobe (G) input. When the strobe is high, all outputs are low. When the strobe is low, a 4-bit word is ...
These quadruple 2-line to 1-line data selectors/multiplexers are designed for 4.5-V to 5.5-V VCC operation. The SN74AHCT158 devices feature a common strobe (G) input. When the strobe is high, all outputs are high. When the strobe is low, a 4-bit word is ...
These data selectors/multiplexers SN74ALS151 provide full binary decoding to select one-of-eight data sources. The strobe (G) input must be at a low logic level to enable the inputs. A high level at the strobe terminal forces the W output high and the Y ...
These dual 1-of-4 data selectors/multiplexers SN74ALS153 contain inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate strobe (G) inputs are provided for each of the two 4-line sections. The SN54ALS153 is ...
These data selectors/multiplexers SN74ALS157A contain inverters and drivers to supply full data selection to the four output gates. A separate strobe (G) input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs. ...
These data selectors/multiplexers SN74ALS158 contain inverters and drivers to supply full data selection to the four output gates. A separate strobe (G) input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs. The ...
These data selectors/multiplexers SN74ALS251 contain full binary decoding to select one-of-eight data sources and feature controlled complementary 3-state outputs. The 3-state outputs can interface with and drive data lines of bus-organized systems. With ...
These data selectors/multiplexers SN74ALS253 contain inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate output control inputs are provided for each of the two 4-line sections. The 3-state outputs can ...
These data selectors/multiplexers SN74ALS257A are designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable () input is at a high logic ...
These data selectors/multiplexers SN74ALS258A are designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable () input is at a high logic ...
The SN74ALS857 are hextuple 2-line to 1-line multiplexers with 3-state outputs. The devices can provide either true (COMP low) or inverted (COMP high) data at the Y outputs. In addition, the SN74ALS857 perform the logical AND function (A B) and the clear ...
These data selectors/multiplexers SN74AS151 provide full binary decoding to select one-of-eight data sources. The strobe (G) input must be at a low logic level to enable the inputs. A high level at the strobe terminal forces the W output high and the Y output ...
These dual 1-of-4 data selectors/multiplexers SN74AS153 contain inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate strobe (G) inputs are provided for each of the two 4-line sections. The SN54ALS153 is ...
These data selectors/multiplexers SN74AS157 contain inverters and drivers to supply full data selection to the four output gates. A separate strobe (G) input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs. The ...
These data selectors/multiplexers SN74AS158 contain inverters and drivers to supply full data selection to the four output gates. A separate strobe (G) input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs. The ...
The SN74AS250A devices provide full binary decoding to select 1-of-16 data inputs or use sources as an input with an inverting W output. The selected sources are buffered with symmetrical propagation delay times. This reduces the possibility of transients ...
These data selectors/multiplexers SN74AS253A contain inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate output control inputs are provided for each of the two 4-line sections. The 3-state outputs can ...
These data selectors/multiplexers SN74AS257 are designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable () input is at a high logic level.
These data selectors/multiplexers SN74AS258 are designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable () input is at a high logic level.
The SN74AS298A is a quadruple 2-input multiplexer with storage that provides essentially the equivalent functional capabilities of two separate MSI functions (SN74AS157 and ?AS175A) in a 16-pin package. When the word-select (WS) input is low, word 1 (A1, ...
These monolithic data selectors/multiplexers SN74F151B provide full binary decoding to select one of eight data sources. The strobe (G) input must be at a low logic level to enable the data selection/multiplexing function. A high level at the strobe terminal ...
These data selectors/multiplexers SN74F153 contain inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate strobe (G) inputs are provided for each of the two 4-line sections. The SN54F153 is characterized for ...
The SN74F157A is a quadruple 2-input data selector/multiplexer featuring a common strobe (G) input. When the strobe is high, all outputs are low. When the strobe is low, a 4-bit word is selected from one of two sources and is routed to the four outputs. The ...
These data selectors/multiplexers SN74F251B contain full binary decoding to select one of eight data sources and feature strobe-controlled complementary outputs. The 3-state outputs can interface with and drive data lines of bus-organized systems. When the ...
These data selectors/multiplexers SN74F253 contain inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate output-control inputs are provided for each of the two 4-line sections. The 3-state outputs can interface ...
The SN74F257 is designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs will not load the data lines when the output enable () input is at a high logic level. The SN54F257 is ...
The SN74F258 is designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs will not load the data lines when the output-enable () input is at a high logic level. The SN54F258 is ...
These data selectors/multiplexers SN74HC151 provide full binary decoding to select one of eight data sources. The strobe (G) input must be at a low logic level to enable the inputs. A high level at the strobe terminal forces the W output high and the Y output ...
This data selector/multiplexer SN74HC151-Q1 provides full binary decoding to select one of eight data sources. The strobe (G) input must be at a low logic level to enable the inputs. A high level at the strobe terminal forces the W output high and the Y ...
Each of these data selectors/multiplexers SN74HC153 contains inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate strobe (G) inputs are provided for each of the two 4-line sections. ...
These data selectors/multiplexers contain inverters and drivers to supply full data selection to the four output gates. A separate strobe (G)\\ input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs. The HC157 ...
These data selectors/multiplexers contain inverters and drivers that supply full data selection to the four output gates. A separate strobe (G) input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs. The ?HC158 ...
These data selectors/multiplexers SN74HC251 contain full binary decoding to select 1-of-8 data sources and feature strobe-controlled complementary 3-state outputs. The 3-state outputs can interface with and drive data lines of bus-organized systems. With ...
Each of these data selectors/multiplexers SN74HC253 contains inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate output-control inputs are provided for each of the two 4-line sections. The 3-state outputs can ...
Each data selector/multiplexer SN74HC253-Q1 contains inverters and drivers to supply full binary decoding data selection to the AND-OR gates. Separate output-control inputs are provided for each of the two 4-line sections. The 3-state outputs can interface ...
These devices are designed to multiplex signals SN74HC257 from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable (G) input is at a high logic level. To ensure the ...
These devices are designed to multiplex signals SN74HC258 from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable (G) input is at a high logic level. To ensure the ...
These data selectors/multiplexers SN74HCT157 contain inverters and drivers to supply full data selection to the four output gates. A separate strobe (G) input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs.
The SN74HCT257 devices are designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable (OE) input is at the high logic level. To ensure the ...
These monolithic data selectors/multiplexers SN74LS151 contain full on-chip binary decoding to select the desired data source. The \'150 selects one-of-sixteen data sources; the \'151A, \'LS151, and \'S151 select one-of-eight data sources. The \'150, \'151A, ...
Each of these monolithic, data selectors/multiplexers SN74LS153 contains inverters and drivers to supply fully complementary, on-chip, binary decoding data selection to the AND-OR gates. Separator strobe inputs are provided for each of the two four-time ...
These monolithic data selectors/multiplexers SN74LS157 contain inverters and drivers to supply full on-chip data selection to the four output gates. A separate strobe input is provided. A 4-bit word is selected from one of two sources and is routed to the ...
These monolithic data selectors/multiplexers SN74LS158 contain inverters and drivers to supply full on-chip data selection to the four output gates. A separate strobe input is provided. A 4-bit word is selected from one of two sources and is routed to the ...
These monolithic data selectors/multiplexers SN74LS251 contain full on-chip binary decoding to select one-of-eight data sources and feature a strobe-controlled three-state output. The strobe must be at a low logic level to enable these devices. The ...
Each of these Schottky-clamped data selectors/multiplexers SN74LS253 contains inverters and drivers to supply fully complementary, on-chip, binary decoding data selection to the AND-OR gates. Separate output control inputs are provided for each of the two ...
These devices are designed to multiplex signals SN74LS257B from four-bit data sources to four-output data lines in bus-organized systems. The 3-state outputs will not load the data lines when the output control pin (G) is at a high-logic level. Series ...
These devices are designed to multiplex signals SN74LS258B from four-bit data sources to four-output data lines in bus-organized systems. The 3-state outputs will not load the data lines when the output control pin (G) is at a high-logic level. Series ...
This monolithic quadruple two-input multiplexer SN74LS399 with storage provides essentially the equivalent functional capabilities of two separate MSI functions (SN54LS157/SN74LS157 and SN54LS175/SN74LS175) in a single 16-pin package. When the ...
The SN74LV157A devices are quadruple 2-line to 1-line data selectors/multiplexers designed for 2-V to 5.5-V VCC operation. These devices contain inverters and drivers to supply full data selection to the four output gates. A separate strobe (G) input is ...
The SN74LVC157A quadruple 2-line to 1-line data selector/multiplexer SN74LVC157A-Q1 is designed for 2.7-V to 3.6-V VCC operation. The device features a common strobe (G) input. When G is high, all outputs are low. When G is low, a 4-bit word is selected from ...
These quadruple 2-line to 1-line data selectors/multiplexers SN74LVC257A are designed for 1.65-V to 3.6-V VCC operation. The ?LVC257A devices are designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The ...
The SN74LVC257A quadruple 2-line to 1-line data selector/multiplexer is designed for 2.7-V to 3.6-V VCC operation. The device is designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do ...
These monolithic data selectors/multiplexers SN74S151 contain full on-chip binary decoding to select the desired data source. The \'150 selects one-of-sixteen data sources; the \'151A, \'LS151, and \'S151 select one-of-eight data sources. The \'150, \'151A, ...
These monolithic data selectors/multiplexers SN74S157 contain inverters and drivers to supply full on-chip data selection to the four output gates. A separate strobe input is provided. A 4-bit word is selected from one of two sources and is routed to the four ...
These devices are designed to multiplex signals from four-bit data sources to four-output data lines in bus-organized systems. The 3-state outputs will not load the data lines when the output control pin (G) is at a high-logic level. Series 54LS and 54S ...
The 54AC151 is a high-speed 8-input digital multiplexer. It provides, in one package, the ability to select one line of data from up to eight sources. The 54AC151 can be used as a universal function generator to generate any logic function of four variables. ...
The 54AC153 is a high-speed dual 4-input multiplexer with common select inputs and individual enable inputs for each section. It can select two lines of data from four sources. The two buffered outputs present data in the true (non-inverted) form. In addition ...
The 54AC157 is a high-speed quad 2-input multiplexer. Four bits of data from two sources can be selected using the common Select and Enable inputs. The four outputs present the selected data in the true (noninverted) form. The 54AC157 can also be used as a ...
The 54AC158 is a high-speed quad 2-input multiplexer. It selects four bits of data from two sources using the common Select and Enable inputs. The four buffered outputs present the selected data in the inverted form. The 54AC158 can also be used as a ...
The 54AC251 is a high-speed 8-input digital multiplexer. It provides, in one package, the ability to select one bit of data from up to eight sources. It can be used as universal function generator to generate any logic function of four variables. Both true ...
