Octal Gigabit Ethernet Transceiver

The TLK2208A is the third generation of Gigabit Ethernet Transceivers from Texas Instruments combining high port density and ultralow power in a small form-factor footprint. The TLK2208A provides for high-speed full-duplex point-to-point data transmissions based on the IEEE 802.3z 1000-Mbps Ethernet specification. The TLK2208A supports data rates from 1.0 Gbps through 1.3 Gbps.
The primary application of this device is to provide building blocks for developing point-to-point baseband data transmission over controlled impedance media of 50 . The transmission media CAN be printed circuit board traces, copper cables or fiber-optical Interface modules. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment.
The TLK2208A performs the data encoding, decoding, serialization, deserialization, Clock extraction and Clock tolerance compensation functions for a physical layer Interface device. Each channel operates at up to 1.3 Gbps providing up to 8.32 Gbps of aggregate data bandwidth over copper or optical-media Interfaces
The TLK2208A supports two selectable reduced-pin-count double-data-rate (DDR) Timing Interfaces nibble mode and multiplexed channel mode, to a protocol device.
In the nibble Interface mode, the parallel Interface accepts nibble-wide unencoded or 8b/10b encoded data aligned to both the rising and falling edges of the transmit Clock
In the multiplexed channel mode, the parallel Interface accepts 8-bit-wide unencoded or 10-bit-wide 8b/10b encoded data with channels A, C, E, and G aligned to the falling edge of the source synchronous transmit Clock and channels B, D, F, and H aligned to the rising edge of the transmit Clock The receive path Interface is done in the same manner.
The TLK2208A aligns the recovered data Clock frequency to the reference Clock on each channel by means of a Clock tolerance compensation circuit and internal FIFO that inserts or drops 20-bit IDLE codes as needed in the interpacket gap (IPG). In synchronous mode, the received data for all channels is aligned to a single receive data Clock that is a buffered version of the reference Clock
The TLK2208A supports a selectable IEEE 802.3z compliant 8b/10b encoder/decoder in all its modes of operation.
The TLK2208A automatically locks onto incoming data without the need to pre-lock.
The TLK2208A provides a comprehensive series of built-in tests for self-test purposes including loopback and PRBS generation and verification. An IEEE 1149.1 JTAG port is also supported to aid in board-manufacturing testing.
The TLK2208A is housed in a small form-factor 1919-mm, 289-terminal BGA with 1,0-mm ball pitch. The ball out and footprint are compatible with those of the PMC-Sierra PM8352 8-channel transceiver.
The TLK2208A is characterized to support the commercial temperature range of 0C to 70C.
The TLK2208A consumes 1.3 W when operating at nominal conditions.
The TLK2208A is designed to be hot-plug capable. A power-on reset puts the serial side output signal terminals TX+/TX? in the high-impedance state during power up.
By Texas Instruments
TLK2208A 's PackagesTLK2208A 's pdf datasheet
TLK2208AGPV BGA
TLK2208AZPV BGA




TLK2208A Pinout, Pinouts
TLK2208A pinout,Pin out
This is one package pinout of TLK2208A,If you need more pinouts please download TLK2208A's pdf datasheet.

TLK2208A circuits will be updated soon..., now you can download the pdf datasheet to check the circuits!

Related Electronics Part Number

Related Keywords:

TLK2208A Pb-Free TLK2208A Cross Reference TLK2208A Schematic TLK2208A Distributor
TLK2208A Application Notes TLK2208A RoHS TLK2208A Circuits TLK2208A footprint