Regulated 3.3-V 50-mA Low-Ripple Charge Pump With Ultra Low Operating Current

The TPS6021x Step-up regulated Charge Pumps generate a 3.3-V 4% output voltage from a 1.8-V to 3.6-V input voltage. These devices are typically powered by two alkaline, NiCd, or NiMH battery cells or by one primary lithium MnO2 (or similar) coin cell and operate down to a minimum supply voltage of 1.6 V. Continuous output current is a minimum of 100 mA for the TPS60210 and TPS60211 and 50 mA for the TPS60212 and TPS60213 all from a 2-V input.
Three operating modes CAN be programmed using the SNOOZE pin. When SNOOZE is low, the device is put into snooze mode. In snooze mode, the device operates with a typical quiescent current of 2 uA while the output voltage is maintained at 3.3 V 6%. This is lower than the self-discharge current of most batteries. Load current in snooze mode is limited to 2 mA. When SNOOZE is high, the device is put into normal operating mode. During normal operating mode, the device operates in the newly developed linskip mode where it switches seamlessly from the power saving pulse-skip mode at light loads to the low-noise constant-frequency linear-regulation mode once the output current exceeds the linskip current threshold of about 7 mA. In this mode, the device operates from the internal Oscillator The device is synchronized to an external Clock signal if SNOOZE is clocked; thus switching harmonics CAN be controlled and minimized.
Only four external capacitors are needed to build a complete low-ripple DC/DC converter. The push-pull operating mode of two single-ended Charge Pumps assures the low output voltage ripple as charge is continuously transferred to the output. All the devices CAN start with full load current. The devices include a low-battery detector that issues a warning if the battery voltage drops below a user-defined threshold voltage or a power-good detector that goes active when the output voltage reaches about 90% of its nominal value. This DC/DC converter requires no inductors; therefore, EMI of the system is reduced to a minimum, making it easier to use in designs. It is available in the small 10-pin MSOP package (DGS).
By Texas Instruments
Part Manufacturer Description Datasheet Samples
TPS60213DGS Texas Instruments Regulated 3.3-V 50-mA Low-Ripple Charge Pump with Ultra Low Operating Current 10-VSSOP -40 to 85
TPS60213DGSR Texas Instruments Regulated 3.3-V 50-mA Low-Ripple Charge Pump with Ultra Low Operating Current 10-VSSOP -40 to 85
TPS60213DGSRG4 Texas Instruments SWITCHED CAPACITOR REGULATOR, 400kHz SWITCHING FREQ-MAX, PDSO10, GREEN, PLASTIC, MSOP-10
TPS60213DGSG4 Texas Instruments Regulated 3.3-V 50-mA Low-Ripple Charge Pump with Ultra Low Operating Current 10-VSSOP -40 to 85
TPS60213 's PackagesTPS60213 's pdf datasheet
TPS60213DGS MSOP
TPS60213DGSG4 MSOP
TPS60213DGSR MSOP
TPS60213DGSRG4 MSOP




TPS60213 Pinout, Pinouts
TPS60213 pinout,Pin out
This is one package pinout of TPS60213,If you need more pinouts please download TPS60213's pdf datasheet.

TPS60213 Application circuits
TPS60213 circuits
This is one application circuit of TPS60213,If you need more circuits,please download TPS60213's pdf datasheet.


Related Electronics Part Number

Related Keywords:

TPS60213 Pb-Free TPS60213 Cross Reference TPS60213 Schematic TPS60213 Distributor
TPS60213 Application Notes TPS60213 RoHS TPS60213 Circuits TPS60213 footprint