Advanced PFC/PWM Combination Controllers

The UCC28510 series of combination PFC PWM Controllers provide complete control functionality for any off-line power system requiring compliance with the IEC1000?3?2 harmonic reduction requirements. By combining the control and drive signals for the PFC and the PWM stages into a single device, significant performance and cost benefits are gained. By managing the modulation mechanisms of the two stages (leading-edge modulation for PFC and trailing-edge modulation for PWM), the ripple current in the boost capacitor is minimized.
Based on the average current mode control architecture with input voltage feedforward of prior PFC/PWM combination controllers, these devices offer performance advantages. Two new key PWM features are programmable maximum duty cycle and the 2x PWM frequency options to the base PFC frequency. For the PFC stage, the devices feature an improved multiplier and the use of a transconductance Amplifier for enhanced transient response.
The core of the PFC section is in a three-input multiplier that generates the reference signal for the line current. The UCC28510 series features a highly linearized multiplier circuit capable of producing a low distortion reference for the line current over the full range of line and load conditions. A low-offset, high-bandwidth current error Amplifier ensures that the actual inductor current (sensed through a resistor in the return path) follows the multiplier output command signal. The output voltage error is processed through a transconductance voltage Amplifier
The transient response of the circuit is enhanced by allowing a much faster charge/discharge of the voltage Amplifier output capacitance when the output voltage falls outside a certain regulation window. A number of additional features such as UVLO circuit with selectable hysteresis levels, an accurate reference voltage for the voltage Amplifier zero power detect, OVP/enable, peak current limit, power limiting, high-current output Gate driver characterize the PFC section.
The PWM section features peak current mode control (with a ramp signal available to add slope compensation), programmable soft-start, accurate maximum duty cycle clamp, peak current limit and high-current output Gate driver. The Oscillator for the combination controller is available in two versions. In UCC28510 UCC28511 UCC28512 and UCC28513 the PWM and the PFC circuits are switched at the same frequency. In the UCC28514 UCC28515 UCC28516 and UCC28517 the PWM stage frequency is twice that of the PFC frequency. The PWM stage is suppressed until the PFC output has reached 90% of its programmed value during startup. During line dropout and turn off, the device allows the PWM stage to operate until the PFC output has dropped to 47% UCC28512 UCC28513 UCC28516 and UCC28517 or 71% UCC28510 UCC28511 UCC28514 and UCC28515 of its nominal value. See available options table on page 1 for a summary of options.
The UCC28510 family also features leading-edge modulation for the PFC stage and trailing-edge modulation for the PWM stage in order to reduce the ripple current in the boost output capacitor. The current Amplifier implementation associated with this scheme also results in better noise immunity.
Available in 20-pin N and DW packages.
By Texas Instruments
Part Manufacturer Description Datasheet Samples
UCC28513DWRG4 Texas Instruments Advanced PFC/PWM Combination Controllers 20-SOIC -40 to 105
UCC28513DWR Texas Instruments Advanced PFC/PWM Combination Controllers 20-SOIC -40 to 105
UCC28513N Texas Instruments Advanced PFC/PWM Combination Controllers 20-PDIP -40 to 105
UCC28513DW Texas Instruments Advanced PFC/PWM Combination Controllers 20-SOIC -40 to 105
UCC28513DWG4 Texas Instruments Advanced PFC/PWM Combination Controllers 20-SOIC -40 to 105
UCC28513 's PackagesUCC28513 's pdf datasheet

UCC28513 Pinout will be updated soon..., now you can download the pdf datasheet to check the pinouts !
UCC28513 Application circuits
UCC28513 circuits
This is one application circuit of UCC28513,If you need more circuits,please download UCC28513's pdf datasheet.

Related Electronics Part Number

Related Keywords:

UCC28513 Pb-Free UCC28513 Cross Reference UCC28513 Schematic UCC28513 Distributor
UCC28513 Application Notes UCC28513 RoHS UCC28513 Circuits UCC28513 footprint