The THS7530 is fabricated using Texas Instruments state-of-the-art BiCom III SiGe complementary bipolar process. The THS7530 is a dc-coupled wide bandwidth amplifier with voltage-controlled gain. The amplifier has high impedance differential inputs and low ...
The VCA2614 is a highly integrated, dual receive channel, Variable Gain Amplifier (VGA) with analog gain control.
The VCA2614s VGA section consists of two parts: the Voltage Controlled Attenuator (VCA) and the Programmable Gain Amplifier (PGA). The gain and ...
The VCA2613 is a dual, Low-Noise Preamplifier (LNP), plus low-noise Variable Gain Amplifier (VGA). The combination of Active Termination (AT) and Maximum Gain Select (MGS) allow for the best noise performance. The VCA2613 also features low crosstalk and ...
The VCA2612 is a highly integrated, dual receive channel, signal processing subsystem. Each channel of the product consists of a low noise preamplifier (LNP) and a Variable Gain Amplifier (VGA). The LNP circuit provides the necessary connections to implement ...
The VCA2616 and VCA2611 are dual, Low-Noise Preamplifiers (LNP), plus low-noise Variable Gain Amplifiers (VGA). The VCA2611 is an upgraded version of the VCA2616. The only difference between the VCA2616 and the VCA2611 is the input structure to the LNP. The ...
This device is a monolithic two-stage high-frequency amplifier with differential inputs and outputs.
Internal feedback provides wide bandwidth, low phase distortion, and excellent gain stability. Variable gain based on signal summation provides large AGC ...
The VCA8617 is an 8-channel Variable Gain Amplifier ideally suited to portable ultrasound applications. Excellent dynamic performance enables use in low-power, high-performance portable applications. Each channel consists of a 20dB gain Low-Noise pre-Amplifier ...
The VCA8613 is an 8-channel Variable Gain Amplifier ideally suited to portable ultrasound applications. Excellent dynamic performance enables use in low-power, high-performance portable applications. Each channel consists of a Low-Noise pre-Amplifier (LNA) and ...
The VCA822 is a dc-coupled, wideband, linear in V/V, continuously variable, voltage-controlled gain amplifier. It provides a differential input to single-ended conversion with a high-impedance gain control input used to vary the gain down 40dB from the nominal ...
The VCA820 is a dc-coupled, wideband, linear in dB, continuously variable, voltage-controlled gain amplifier. It provides a differential input to single-ended conversion with a high-impedance gain control input used to vary the gain down 40dB from the nominal ...
The VCA810 is a DC-coupled, wideband, continuously variable, voltage-controlled gain amplifier. It provides a differential input to single-ended output conversion with a high-impedance gain control input used to vary the gain over a 40dB to +40dB range linear ...
The VCA2615 is a dual-channel Variable Gain Amplifier consisting of a Low-Noise Preamplifier (LNP) and a Variable-Gain Amplifier (VGA). This combination along with the device features makes it well-suited for a variety of ultrasound systems.
The LNP offers ...
The VCA2619 is a highly integrated, dual receive channel, Variable Gain Amplifier (VGA) with analog gain control.
The VCA2619s VGA section consists of two parts: the Voltage Controlled Attenuator (VCA) and the Programmable Gain Amplifier (PGA). The gain and ...
The VCA2618 is a highly integrated, dual receive channel, Variable Gain Amplifier (VGA) with analog gain control.
The VCA2618s VGA section consists of two parts: the Voltage Controlled Attenuator (VCA) and the Programmable Gain Amplifier (PGA). The gain and ...
The VCA2617 is a dual-channel, continuously variable, voltage-controlled gain amplifier well-suited for a variety of ultrasound systems as well as applications in proximity detectors and test equipment. The VCA2617 uses a true variable-gain amplifier ...
The VCA2616 and VCA2611 are dual, Low-Noise Preamplifiers (LNP), plus low-noise Variable Gain Amplifiers (VGA). The VCA2611 is an upgraded version of the VCA2616. The only difference between the VCA2616 and the VCA2611 is the input structure to the LNP. The ...
The CLC5526 is a high performance, digitally controlled, variable-gain amplifier (DVGA). It has been designed for use in a broad range of mixed signal and digital communication applications such as mobile radio, cellular base stations and back-channel modems ...
The CLC522 Variable Gain Amplifier (VGA) is a dc-coupled, two-quadrant multipliers with differential voltage inputs and a single-ended voltage output. Two input buffers and an output operational amplifier are integrated with the multiplier core and make the ...
The LMH6505 is a wideband DC coupled voltage controlled gain stage followed by a high-speed current feedback op amp which can directly drive a low impedance load. The gain adjustment range is 80 dB for up to 10 MHz which is accomplished by varying the gain ...
The CLC520 is a wideband DC-coupled amplifier with voltage controlled gain (AGC). The amplifier has a high impedance, differential signal input; a high bandwidth, gain control input; and a single-ended voltage output. Signal channel performance is outstanding ...
The LMH?6502 is a wideband DC coupled differential input voltage controlled gain stage followed by a high-speed current feedback Op Amp which can directly drive a low impedance load. Gain adjustment range is more than 70dB for up to 10MHz. Maximum gain is ...
The LMH?6503 is a wideband DC coupled differential input voltage controlled gain stage followed by a high-speed current feedback Op Amp which can directly drive a low impedance load. Gain adjustment range is more than 70dB for up to 10MHz. Maximum gain ...
The LMH6515 is a high performance, digitally controlled Variable Gain Amplifier (DVGA). It combines precision gain control
with a low noise, ultra-linear, differential amplifier. Typically, the LMH6515 drives a high performance ADC in a broad range
of mixed ...
The AD600/AD602 dual channel, low noise, variable gain
amplifiers are optimized for use in ultrasound imaging systems
but are applicable to any application requiring precise gain, low
noise and distortion, and wide bandwidth. Each independent
channel ...
The AD600/AD602 dual channel, low noise, variable gain
amplifiers are optimized for use in ultrasound imaging systems
but are applicable to any application requiring precise gain, low
noise and distortion, and wide bandwidth. Each independent
channel ...
The AD603 is a low noise, voltage-controlled amplifier for use in RF and IF AGC systems. It provides accurate, pin-selectable gains of 11 dB to +31 dB with a bandwidth of 90 MHz or +9 dB to 51+ dB with a bandwidth of 9 MHz. Any intermediate gain range may be ...
The AD604 is an ultralow noise, very accurate, dual-channel, linear-in-dB Variable Gain Amplifier (VGA) optimized for time-based variable gain control in ultrasound applications; however, it supports any application requiring low noise, wide bandwidth, ...
The AD605 is a low noise, accurate, dual-channel, linear-in-dB Variable Gain Amplifier (VGA), optimized for any application requiring high performance, wide bandwidth variable gain control. Operating from a single 5 V supply, the AD605 provides differential ...
The AD8320 is made up of a digitally controlled variable attenuator
of 0 dB to 36 dB, which is preceded by a low noise,
fixed gain buffer and followed by a low distortion high power
amplifier. The AD8320 has a 220 ohm input impedance and accepts
a ...
The AD8321 is a low cost digitally controlled variable gain
amplifier optimized for coaxial line driving applications such as
cable modems that are designed to the DOCSIS* (upstream
standard. An 8-bit serial word determines the desired output gain
over a ...
The AD8323 is a low cost digitally controlled variable gain
amplifier optimized for coaxial line driving applications such as
cable modems that are designed to the MCNS-DOCSIS upstream
standard. A 8-bit serial word determines the desired output gain
over a ...
The AD83301 is a wideband Variable Gain Amplifier for applications requiring a fully-differential signal path, low noise, well-defined gain, and moderately low distorion, from dc to 150 MHz. The input pins can also be driven from a single ended source. The ...
The AD8331 is a single, ultralow noise, linear-in-dB, Variable Gain Amplifier (VGA). Optimized for ultrasound systems, it is usable as a low noise variable gain element at frequencies up to 120 MHz. Included is an ultralow noise preamplifier (LNA), an ...
The AD8332 is a dual channel ultralow noise, linear-in-dB, Variable Gain Amplifier (VGA). Optimized for ultrasound systems, they are usable as a low noise variable gain element at frequencies up to 120 MHz. Included in each channel are an ultralow noise ...
The AD8334 is an ultralow noise, quad channel linear-in-dB Variable Gain Amplifier (VGA). Although optimized for ultrasound systems, it may be used as a low noise variable gain control in any application whose operating frequency is less than 100 MHz.
The AD8335 is a quad Variable Gain Amplifier (VGA) with low noise preamplifier intended for cost and power sensitive applications. AD8335 features four channels with 48 dB gain range; fully differential signal paths; and active input preamplifier matching. The ...
The AD8336 is a low noise single ended linear-in-dB, general purpose Variable Gain Amplifier usable as a low noise variable gain element over a large supply voltage range. For example, at 5 V supplies, the part can be used for frequencies up to 80 MHz (2 V ...
The AD8337 is a low noise, single-ended, linear-in-dB, general-purpose Variable Gain Amplifier (VGA) usable at frequencies from dc to 100 MHz; the 3 dB bandwidth is 280 MHz. Excellent bandwidth uniformity across the entire gain range and low output-referred ...
The AD8367 is a high-performance Variable Gain Amplifier designed to be used at IF frequencies up to 500 MHz. An externally applied analog gain control voltage of 0 to 1 volt, scales the 45 dB of gain control range to provide 20 mV/dB output. The precise ...
The AD8368 is a Variable Gain Amplifier (VGA) with analog linear-in-dB gain control that can be used from low frequencies to 800 MHz. Its excellent gain range, conformance, and flatness are attributed to the Analog Devices, Inc. X-AMP architecture, an ...
The AD8369 is a high performance, digitally controlled Variable Gain Amplifier designed to be used at IF frequencies within cellular receivers. The device features a 4-bit digitally controlled gain control interface configurable for either parallel or 3 ...
The AD8370 is a high performance, digitally controlled Variable Gain Amplifier designed to be used at IF frequencies within communication infrastructure equipment. The part provides two gain control ranges that are controlled through a three wire digital ...
The AD8375 is a digitally controlled, variable gain, wide bandwidth amplifier that provides precise gain control, high IP3, and low noise figure. The excellent distortion performance and high signal bandwidth make the AD8375 an excellent gain control device ...
The AD8376 is a dual channel, digitally controlled, variable gain wide bandwidth amplifier that provides precise gain control, high IP3, and low noise figure. The excellent distortion performance and high signal bandwidth make the AD8376 an excellent gain ...
The ADL5330 is a broadband voltage Variable Gain Amplifier specified for operation from 10MHz to 3GHz. The device provides precise linear-in-dB gain control over 60dB range with approximately -40dB attenuation and +20dB gain.
A 0 to 1.4V gain control input ...
The SA5209 represents a breakthrough in monolithic amplifier design featuring several innovations. This unique design has combined the advantages of a high speed bipolar process with the proven Gilbert architecture. The SA5209 is a linear broadband RF ...
The SA5219 represents a breakthrough in monolithic amplifier design featuring several innovations. This unique design has combined the advantages of a high speed bipolar process with the proven Gilbert architecture.The SA5219 is a linear broadband RF amplifier ...
BGA2031/1 MMIC Variable Gain Amplifier Silicon Monolitic Microwave Integrated Circuit (MMIC)
2 stage Variable Gain Amplifier in double polysilicon
technology in a 6-pin SOT363 SMD plastic package for low
voltage medium power applications.
...
The MAX2057 general-purpose, high-performance variable-gain amplifier (VGA) is designed to operate in the 1700MHz to 2500MHz frequency range . This device features 15.5dB of gain, 6dB of noise figure, and an output 1dB compression point of 23.8dBm. The MAX2057 ...
The MAX2056 general-purpose, high-performance variable-gain amplifier (VGA) is designed to operate in the 800MHz to 1000MHz frequency range . This device features 15.5dB of gain, 4.5dB of noise figure, and an output 1dB compression point of 23.5dBm. The ...
The MAX2059 high-linearity digital-variable-gain amplifier (DVGA) is designed to provide 56dB of total gain range and typical output IP3 and output P1dB levels of +31.8dBm
and +18.4dBm, respectively. The device is ideal for a variety of applications, ...
The MAX2058 high-linearity digital-variable-gain amplifier (DVGA) is designed to provide 62dB of total gain range and typical output IP3 and output P1dB levels of +32.3dBm and +19dBm, respectively. The device is ideal for a variety of applications, including ...
The MAX2027 high-performance, digitally controlled
variable-gain amplifier is designed for use from 50MHz
to 400MHz. The device integrates a digitally controlled attenuator
and a high-linearity IF amplifier in one package.
Targeted for IF signal ...
The HMC463 is a GaAs MMIC PHEMT Low Noise AGC Distributed Amplifier die which operates between 2 and 20 GHz. The amplifier provides 14 dB of gain, 2.5 dB noise figure and 19 dBm of output power at 1 dB gain compression while requiring only 60 mA from a ...
The HMC463LH250 is a GaAs MMIC PHEMT Low Noise AGC Distributed Amplifier packaged in a hermetic surface mount package which operates between 2 and 20 GHz. The amplifier provides 13 dB of gain, 3.0 dB noise figure and 18 dBm of output power at 1 dB gain ...
The HMC625LP5(E) is a digitally controlled Variable Gain Amplifier which operates from DC to 6 GHz, and can be programmed to provide anywhere from 13.5 dB attenuation, to 18 dB of gain, in 0.5 dB steps. The HMC625LP5(E) delivers noise fi gure of 6 dB in its ...
The HMC626LP5(HMC626LP5E) is a digitally controlled Variable Gain Amplifier which operates from DC to 1 GHz, and can be programmed to provide anywhere from 8.5 dB, to 40 dB of gain, in 0.5 dB steps. The HMC626LP5( HMC626LP5E ) delivers noise figure of 4 dB in ...
The HMC627LP5(HMC627LP5E) is a digitally controlled Variable Gain Amplifier which operates from 50 MHz to 1 GHz, and can be programmed to provide anywhere from 11.5 dB attenuation, to 20 dB of gain, in 0.5 dB steps. The HMC627LP5( HMC627LP5E ) delivers noise ...
The HMC628LP4(HMC628LP4E) is a digitally controlled Variable Gain Amplifier which operates from 50 to 800 MHz, and can be programmed to provide anywhere from 8 dB attenuation, to 15 dB of gain, in 1 dB steps. The HMC628LP4(E) delivers noise figure of 5 dB in ...
The HMC640LP5(HMC640LP5E) is an analog controlled Variable Gain Amplifier which operates from 0.4 to 3 GHz, and can be controlled to provide anywhere from 20 dB attenuation, to 25 dB of gain. The HMC640LP5(E) delivers noise figure of 5 dB in its maximum gain ...
The uPC3219GV is a silicon monolithic IC designed for use as AGC amplifier for digital CATV, cable modem
systems. This IC consists of gain control amplifier and video amplifier. ...
The uPC3217GV , uPC3218GV are silicon monolithic ICs designed for use as AGC amplifier for digital CATV, cable
modem systems. These ICs consist of gain control amplifier and video amplifier.
The package is 8-pin SSOP suitable for surface mount. ...
The uPC3231GV is a silicon monolithic IC designed for use as AGC amplifier for digital CATV, cable modem and
digital terrestrial systems. This IC consists of gain control amplifier and video amplifier. ...
The uPC3234GV is a silicon monolithic IC designed for use as AGC amplifier for digital CATV, cable modem and
digital terrestrial systems. This IC consists of gain control amplifier and video amplifier. ...
The uPC8204TK is a silicon monolithic integrated circuit designed as Variable Gain Amplifier The package is 6-pin
lead-less minimold suitable for surface mount. ...
The SA2159 is a voltage-controlled amplifier (VCA) circuit. The chip is a
high-performance currentin/current-out devices including two opposing-
polarity, voltage-sensitive control ports. Due to super low-noise
application, the circuit adopts ...
SA8507 is a automatic gain control system that is used for dynamic
range compression and expansion. According to the companding the
signal, this can reduce the noise components. SA8507 includes
compressor, expander, pre-amp, filter ...
he MPS-032701A-82 is an internally matched GaAs FET amplifier in a surface mount
ceramic package. It is ideal for digital communications applications where excellent gain
linearity and high efficiency at a 5 Volt bias is required. The device may be ...
The AD8260 includes a high current driver, usable as a
transmitter, and a low noise digitally programmable variable
gain amplifier (DGA), useable as a receiver.
The receiver section consists of a single-ended input preampli-
fier, and linear-in-dB, ...
The IVA-14 series MMlCs are
variable gain amplifiers. The
IVA-14208 is housed in a miniature
low cost plastic surface mount
package. The IVA-14228 is housed
in a miniature hermetic ceramic
surface mount package. Both
devices can be used in ...
The LMH6514 is a high performance, digitally controlled vari-
able gain amplifier (DVGA). It combines precision gain control
with a low noise, ultra-linear, differential amplifier. Typically,
the LMH6514 drives a high performance ADC in a broad
range of ...
The SSM2018T and SSM2118T represent continuing evolu-
tion of the Frey Operational Voltage Controlled Element
(OVCE) topology that permits flexibility in the design of high
performance volume control systems. Voltage (SSM2018T)
and differential current ...
The SP8024, SP8025, and SP8026 are high-speed, differential output APC amplifiers that
integrate the photodiode and adjustable gain block on one chip. This allows the user to control
the laser power of the system in high-speed DVDRW, DVDRAM and CDRW ...
The SP8027 represents the next generation in Automatic Power Control (APC) amplifiers designed
specifically for demanding pick-up head applications. Whereas typical APC products exhibit
degradation of bandwidth and slower settling times at higher gain ...